Коды ошибок копировальных аппаратов
Ricoh, Gestetner, Nashuatec, Rex-Rotary
Если Ваш копировальный аппарат Ricoh, Gestetner, Nashuatec,
Rex-Rotary выдал на индикации некий код, то узнать причину
возникновения ошибки Вы можете в этом разделе.
Но код ошибки - это лишь следствие сбоя в работе аппарата
Ricoh 2010, 2050, 2070
| Код ошибки |
Описание |
| E1 |
Exposure lamp |
| E2 |
Scan |
| E5 |
Fuser |
| E6 |
Drive |
| E7 |
Master |
| E8 |
Exp. Lamp heater/Exp. Lamp thermistor of thermofuse |
| E9 |
Optics board |
| EA |
Interface - sorter |
Ricoh
3013, 3213
| Код ошибки |
Описание |
| 11 |
Exposure lamp open |
| 12 |
Exposure lamp stays on |
| 12 |
Zero cross. Main board or DC power supply |
| 21 |
Scan home problem (did not return home) |
| 22 |
Scan home problem (did not leave home) |
| 28 |
Lens home problem (did not get home) |
| 29 |
Lens home problem (did not leave home) |
| 2A |
Mirror home problem (did not get home) |
| 2B |
Mirror home problem (did not leave home) |
| 40 |
Optics thermistor open |
| 52 |
Low fuser temperature. Lamp, thermal switch, thermistor |
| 53 |
High fuser temperature. Themistor, AC driver, pinched wire |
| 55 |
Fuser thermistor open |
| 70 |
Waste toner. 80K copies or 9 toner cartridges have been run.
Reset with SP mode 83 |
| 96 |
Document feeder drive problem |
| U2 |
User code. Key counter not
installed |
Ricoh 3020, 3050,
3060
| Код ошибки |
Описание |
| E1 |
Scanner of Exp. Lamp |
| E2 |
Main drive or relay RA2 |
| E3 |
Fuser |
| E4 |
Total counter |
| U1 |
Interlock or thermal fuse |
| U2 |
Key counter |
| U3 |
Oil (later machines) |
Ricoh
3320
| Код ошибки |
Описание |
| E1 |
Exposure lamp |
| E2 |
Scan problem |
| E5 |
Fuser |
| E6 |
Drive |
| E7 |
Toner waste is full |
| U3 |
Developer unit is not installed |
| U5 |
Add fuser oil |
Ricoh 3513,
3713
| Код ошибки |
Описание |
| 11 |
Exposure lamp open |
| 12 |
Exposure lamp stays on |
| 21 |
Scan home problem |
| 22 |
Scan home problem(did not return home) |
| 28 |
Lens home problem (did not get home) |
| 29 |
Lens home problem (did not leave home) |
| 2A |
Mirror home problem (did not get home) |
| 2B |
Mirror home problem (did not leave home) |
| 40 |
Optics thermistor open |
| 52 |
Low fuser temperature. Lamp, thermal switch, thermistor |
| 53 |
High fuser temperature. Thermistor, AC driver, pinched
wire |
| 54 |
Fuser low temperature on early EPROM |
| 55 |
Fuser thermistor open |
Ricoh
4015
| Код ошибки |
Описание |
| E11 |
Exposure lamp problem |
| E12 |
Exposure lamp problem |
| E13 |
Zero cross. Main board or power supply board |
| E14 |
Same as E13 |
| E21 |
Scan home problem |
| E22 |
Scan home problem |
| E28 |
Lens home sensor |
| E29 |
Lens home problem |
| E2A |
4th & 5th mirror home problem |
| E2B |
4th & 5th mirror home problem. Fuse 2 on AC/DC board |
| E40 |
Optics thermistor |
| E42 |
Bad transfer corona or HVT |
| E52 |
Low fuser temperature |
| E53 |
High fuser temperature |
| E54 |
Fuser lamp on too long |
| E55 |
Fuser thermistor open |
| U1 |
Right side open |
| U2 |
No key counter |
| U4 |
Sorter not latched, not closed |
| U6 |
Developer unit not in place |
Ricoh 4022, 4027
| Код ошибки |
Описание |
| C1 |
Front door open |
| C2 |
Exit door |
| C3 |
Cassette cover |
| C4 |
LCT cover |
| C5 |
Sorter open or not latched to machine, or fuse 304 on DC power
board |
| C6 |
ADF cover |
| C7 |
Right side cover |
| E101 |
Exposure lamp too long |
| E103 |
Frequency problem |
| E120, 121 |
Scan home problem |
| E124 |
Scan drive problem |
| E140 |
Lens home, or fuse 303 on DC board |
| E141-143 |
Lens home sensor, fuse 303 on DC board |
| E144, 145 |
Mirror sensor, fuse 303 on DC board |
| E191 |
Image density sensor error |
| E302 |
Charge roller problem or HVT problem |
| E346 |
Bias loss |
| E351 |
Image density sensor problem |
| E352 |
TD sensor error |
| E353 |
Vsp problem. Dirty or bad image density sensor |
| E354 |
Vsg problem. Same as E353 |
| E355 |
Toner density sensor problem |
| E356 |
Same as 355 |
| E405 |
Transfer belt or charge roller drive |
| E440 |
Main drive |
| E442 |
Drum charge thermistor |
| E501 |
Upper lift motor |
| E502 |
Lower lift motor |
| E503 |
1st tray motor |
| E504 |
2nd tray motor |
| E505 |
3rd tray motor |
| E506 |
Tray main motor drive problem |
| E507 |
LCTl lift motor |
| E522-525 |
Jogger sensor |
| E541 |
Fuser thermistor |
| E542 |
Fuser temperature too low |
| E543 |
Fuser temperature too high |
| E544 |
Fuser temperature too high |
| E547 |
Fuser lamp won't shut off |
| E548 |
Fuser temperature too high or too low |
| E620 |
Communication problem between main board and ARDF |
| E621 |
Communication problem between main board and sorter |
| E623 |
Communication problem between main board and paper trays |
| E720 |
Sorter stapler timing roller sensor |
| E721 |
Sorter stapler bin lift sensor |
| E722 |
Sorter stapler jogger sensor |
| E723 |
Sorter stapler grip sensor |
| E724 |
Sorter stapler error |
| E900, 901 |
Copy counter |
| U2 |
Key counter |
| U6 |
Fuser unit not installed properly |
| U7 |
Duplex unit |
Ricoh
4065
| Код ошибки |
Описание |
| E1 |
Exposure lamp |
| E2 |
Lamp relay |
| E3 |
Registration start switch |
| E4 |
Scan not home |
| E5 |
No home position |
| E6 |
lens home switch not on |
| E7 |
Lens home switch off |
| E8, E9 |
Encoder |
| EA |
Thermofuse |
| Eb |
Thermistor |
| EC |
Not ready |
| Ed |
Pulse generator |
| EE |
Total counter |
| EF |
Optics |
Ricoh 4085
| Код ошибки |
Описание |
| 11 |
Exposure lamp |
| 12 |
Lamp relay |
| 20 |
Low frequency encoder output |
| 21 |
Scan |
| 23 |
No registration start signal |
| 24 |
No home position |
| 28 |
Lens home position not on |
| 29 |
Lens home position not off |
| 52 |
Thermofuse |
| 53 |
Thermistor |
| 54 |
Not ready |
| 61 |
Pulse generator |
| 91 |
Total counter |
| 93 |
Interface |
Ricoh 4215, 4220,
4222
| Код ошибки |
Описание |
| E11 |
Exposure lamp problem |
| E12 |
Exposure lamp problem |
| E13 |
Zero cross |
| E21, 22 |
Scan home problem. Fuse 102 on DC power supply |
| E28, 29 |
Lens home problem |
| E2A |
4th & 5th mirror home problem. Fuse 101 on DC power
supply |
| E2B |
4th & 5th mirror home problem |
| E52 |
Low fuser temperature |
| E53 |
High fuser temperature |
| E55 |
Fuser thermistor open |
| E70 |
Waste toner full |
| E80 |
Communication problem between copier and duplex unit. Fuse 100
or 101 on DC power supply bored |
| E82, 83 |
Jogger home problem |
| U1 |
Right side open |
| U2 |
No key counter |
| U4 |
Sorter not latched or not closed |
| U5 |
Cassette lift sensor |
| U7 |
Duplex open |
Ricoh
4400
| Код ошибки |
Описание |
| 11 |
Exposure lamp |
| 12 |
Exposure lamp stays on |
| 21, 22 |
Scan not home |
| 23 |
No signal from registration switch |
| 24 |
Scan not home |
| 25 |
Scan |
| 28 |
Lens not home |
| 29 |
Lens won't leave home |
| 2A |
Second scan sensor |
| 2A |
Mirror sensor stays actuated |
| 2B |
Mirror sensor stays actuated |
| 2B |
Scan sensor |
| 2C |
Scanner moving too fast |
| 2D |
Scanner moving too slowly or not moving |
| 31 |
Drum thermistor |
| 32 |
Toner sensor |
| 41 |
Third cassette lift motor sensor |
| 52 |
Fuser thermofuse |
| 53 |
Fuser thermistor |
| 54 |
Low temperature at warm up |
| 55 |
High temperature at warm up |
| 56 |
Low temperature after warm up |
| 61 |
Pulse generator |
| 81, 82 |
Duplex jogger |
| 82 |
Duplex jogger |
| 91 |
Counter |
| 93 |
Main board |
Ricoh
4410
| Код ошибки |
Описание |
| 11 |
Exposure lamp |
| 21 |
Scan not home |
| 23 |
No signal from regulator switch |
| 24 |
Scan not home |
| 28 |
Lens not home |
| 29 |
Lens won't leave home |
| 2A |
Second scan flasher |
| 2B |
Scan sensor |
| 2C |
Scanner moving too fast |
| 2D |
Scanner moving too slowly |
| 31 |
Drum thermistor |
| 32 |
Toner sensor |
| 41 |
Third cassette lift motor sensor |
| 53 |
Fuser thermistor |
| 54 |
Low temperature at warm up |
| 55 |
High temperature at warm up |
| 56 |
Low temperature after warm up |
| 61 |
Pulse generator |
| 91 |
Counter |
| 93 |
Main board |
Ricoh
4420
| Код ошибки |
Описание |
| E1 |
Exposure lamp |
| E2 |
Lamp relay |
| E3 |
Registration start switch |
| E4 |
Scan not home |
| E5 |
No home position |
| E6 |
lens home switch not on |
| E7 |
Lens home switch off |
| E8, E9 |
Encoder |
| EA |
Thermofuse |
| Eb |
Thermistor |
| EC |
Not ready |
| Ed |
Pulse generator |
| EE |
Total counter |
| EF |
Optics |
Ricoh 4421
| Код ошибки |
Описание |
| 21, 22 |
Scanner home position error |
| 28, 29 |
Lens home position error |
| 2A, 2B |
4th/5th mirror home position error |
Ricoh 4430, 4460,
4480, 4490
| Код ошибки |
Описание |
| 11 |
Exposure lamp |
| 21 |
Scan not home |
| 23 |
No signal from regulator switch |
| 24 |
Scan not home |
| 28 |
Lens not home |
| 29 |
Lens won't leave home |
| 2A |
Second scan flasher |
| 2B |
Scan sensor |
| 2C |
Scanner moving too fast |
| 2D |
Scanner moving too slowly |
| 31 |
Drum thermistor |
| 32 |
Toner sensor |
| 41 |
Third cassette lift motor sensor |
| 53 |
Fuser thermistor |
| 54 |
Low temperature at warm up |
| 55 |
High temperature at warm up |
| 56 |
Low temperature after warm up |
| 61 |
Pulse generator |
| 91 |
Counter |
| 93 |
Main board |
Ricoh 4522,
4527
| Код ошибки |
Описание |
| C1 |
Front door open |
| C2 |
Exit door |
| C3 |
Cassette cover |
| C4 |
LCT cover |
| C5 |
Sorter open or not latched to machine, or fuse 304 on DC power
board |
| C6 |
ADF cover |
| C7 |
Right side cover |
| E101 |
Exposure lamp too long |
| E103 |
Frequency problem |
| E120, 121 |
Scan home problem |
| E124 |
Scan drive problem |
| E140-143 |
Lens home, or fuse 303 on DC board |
| E144, 145 |
Mirror sensor, fuse 303 on DC board |
| E191 |
Image density sensor error |
| E302 |
Charge roller problem or HVT problem |
| E346 |
Bias loss |
| E351 |
Image density sensor problem |
| E352 |
TD sensor error |
| E353, 354 |
Vsp problem. Dirty or bad image density sensor |
| E355, 356 |
Toner density sensor problem |
| E405 |
Transfer belt or charge roller drive |
| E440 |
Main drive |
| E442 |
Drum charge thermistor |
| E501 |
Upper lift motor |
| E502 |
Lower lift motor |
| E503 |
1st tray motor |
| E504 |
2nd tray motor |
| E505 |
3rd tray motor |
| E506 |
Tray main motor drive problem |
| E507 |
LCTl lift motor |
| E522-525 |
Jogger sensor |
| E541 |
Fuser thermistor |
| E542 |
Fuser temperature too low |
| E543 |
Fuser temperature too high |
| E544 |
Fuser temperature too high |
| E547 |
Fuser lamp won't shut off |
| E548 |
Fuser temperature too high or too low |
| E620 |
Communication problem between main board and ARDF |
| E621 |
Communication problem between main board and sorter |
| E623 |
Communication problem between main board and paper trays |
| E720 |
Sorter stapler timing roller sensor |
| E721 |
Sorter stapler bin lift sensor |
| E722 |
Sorter stapler jogger sensor |
| E723 |
Sorter stapler grip sensor |
| E724 |
Sorter stapler error |
| E900, 901 |
Copy counter |
| U2 |
Key counter |
| U6 |
Fuser unit not installed properly |
| U7 |
Duplex unit |
Ricoh 5000,
5010
| Код ошибки |
Описание |
| 11 |
Exposure lamp |
| 12 |
Exposure lamp relay |
| 21-24 |
Scan |
| 25 |
Scan motor |
| 28 |
Lens position |
| 2A, 2B |
2nd scan home |
| 2C, 2D |
Scan motor |
| 2E |
Encoder |
| 31 |
Drum thermistor |
| 43 |
Lower paper feed |
| 52 |
Thermofuse |
| 53 |
Thermistor |
| 54 |
No heat |
| 55 |
Overheat |
| 61 |
Drive system |
| 81, 82 |
Jogger problem |
| 91 |
Counter |
| 93 |
Optics and main board interface |
| 94 |
Optics board and main board
interface |
Ricoh 5035,
5535
| Код ошибки |
Описание |
| C1 |
Front door open |
| C2 |
Exit door |
| C3 |
Cassette cover |
| C4 |
LCT cover |
| C5 |
Sorter open or not latched to machine, or fuse 304 on DC power
board |
| C6 |
ADF cover |
| C7 |
Right side cover |
| E101 |
Exposure lamp on too long |
| E103 |
Frequency problem |
| E120, 121 |
Scan home problem |
| E124 |
Scan drive problem |
| E140-143 |
Lens home, or fuse 303 on DC board |
| E144, 145 |
Mirror sensor, fuse 303 on DC board |
| E191 |
Image density sensor problem |
| E302 |
Charge roller problem or HVT problem |
| E346 |
Bias loss |
| E351 |
Image density sensor error |
| E352 |
TD sensor error |
| E353, 354 |
Vsp problem. Dirty or bad image density sensor |
| E355 |
Toner density sensor problem |
| E356 |
Vsp problem. Dirty or bad image density sensor |
| E405 |
Transfer belt or charge roller drive |
| E440 |
Main drive |
| E442 |
Drum charge thermistor |
| E501 |
Upper lift motor |
| E502 |
Lower lift motor |
| E503 |
1st tray motor |
| E504 |
2nd tray motor |
| E505 |
3rd tray motor |
| E506 |
Tray main motor drive problem |
| E507 |
LCT lift motor |
| E522-525 |
Jogger sensor |
| E541 |
Fuser thermistor |
| E542 |
Fuser temperature too low |
| E543 |
Fuser temperature too high |
| E544 |
Fuser temperature too high |
| E547 |
Fuser lamp won't shut off |
| E548 |
Fuser temperature too high or too low |
| E620 |
Communication problem between main board and ARDF |
| E621 |
Communication problem between main board and sorter |
| E623 |
Communication problem between main board and paper trays |
| E720 |
Sorter stapler timing roller sensor |
| E721 |
Sorter stapler bin lift sensor |
| E722 |
Sorter stapler jogger sensor |
| E723 |
Sorter stapler grip sensor |
| E724 |
Sorter stapler error |
| E900, 901 |
Copy counter |
| U2 |
Key counter |
| U6 |
Fuser unit not installed properly |
| U7 |
Duplex unit |
Ricoh 5050,
5070
| Код ошибки |
Описание |
| 11 |
Exposure lamp |
| 12 |
Exposure lamp relay |
| 21-24 |
Scan |
| 28 |
Lens position |
| 29 |
Lens |
| 2A-2D |
Scan |
| 41 |
Upper paper feed |
| 43 |
Lower paper feed |
| 52 |
Thermofuse |
| 53 |
Thermistor |
| 54 |
No heat |
| 61 |
Drive |
| 81 |
Jogger |
| 91 |
Counter |
| 93 |
Main board or optics |
Ricoh
5540
| Код ошибки |
Описание |
| 11 |
Exposure lamp |
| 12 |
Exposure lamp stays on |
| 21 |
Scan not home |
| 22 |
Scan not home |
| 23 |
So signal from registration switch |
| 24 |
Scan not home |
| 25 |
Scan |
| 28 |
Lens not home |
| 29 |
Lens won't leave home |
| 2A |
Second scan sensor |
| 2A |
Mirror sensor stays actuated |
| 2B |
Mirror sensor stays actuated |
| 2B |
Scan sensor |
| 2C |
Scanner moving to fast |
| 2D |
Scanner moving too slowly or not moving |
| 31 |
Drum thermistor |
| 32 |
Toner sensor |
| 41 |
Third cassette lift motor sensor |
| 52 |
Fuser thermofuse |
| 53 |
Fuser thermistor |
| 54 |
Low temperature at warm up |
| 55 |
High temperature at warm up |
| 56 |
Low temperature after warm up |
| 61 |
Pulse generator |
| 81 |
Duplex jogger |
| 82 |
Duplex jogger |
| 91 |
Counter |
Ricoh 5560
| Код ошибки |
Описание |
| 11 |
Exposure lamp |
| 12 |
ExpExposure lamp relay |
| 21 |
Scan home switch not actuated |
| 22 |
Scan home switch activated |
| 23 |
Scan registration switch |
| 24 |
Scan home problem |
| 25 |
Scan motor |
| 28 |
Lens home switch not actuated |
| 29 |
Lens home switch actuated |
| 2A |
2nd scan home switch not actuated |
| 2b |
2nd home scan switch actuated |
| 2c |
Encoder (high frequency) |
| 2d |
Encoder (low frequency) |
| 2E |
No encoder |
| 31 |
Drum thermistor |
| 52 |
Fuser thermofuse (or F3) |
| 53 |
Fuser thermistor |
| 54 |
No ready |
| 55 |
High temperature |
| 61 |
Pulse generator |
| 81 |
Jogger home switch not actuated |
| 82 |
Jogger home switch actuated |
| 91 |
Total counter |
| 94 |
Data transfer problem between main board and operations
board |
Ricoh 5632, 5732, 5832,
5840
| Код ошибки |
Описание |
| C1 |
Front door open |
| C2 |
Exit door |
| C3 |
Cassette cover |
| C4 |
LCT cover |
| C5 |
Sorter open/not latched to machine |
| C6 |
ADF cover |
| C7 |
Right side cover |
| E101 |
Exposure lamp on too long |
| E103 |
Frequency problem |
| E120, 121 |
Scan home problem |
| E124 |
Scan drive problem |
| E140-143 |
Lens home, or fuse 303 on DC board |
| E144, 145 |
Mirror sensor, fuse 303 on DC board |
| E191 |
Image density sensor problem |
| E302 |
Charge roller or HVT problem |
| E346 |
Bias loss |
| E351 |
Image density sensor problem |
| E352 |
TD sensor error |
| E353, 354 |
Vsp problem |
| E355, 356 |
Toner density sensor problem |
| E405 |
Transfer belt or charge roller drive |
| E440 |
Main drive |
| E442 |
Drum charge thermistor |
| E501 |
Upper lift motor |
| E502 |
lower lift motor |
| E503 |
1st tray motor |
| E504 |
2nd tray motor |
| E505 |
3rd tray motor |
| E506 |
Tray main motor drive problem |
| E507 |
LCT lift motor |
| E522-525 |
Jogger sensor |
| E541 |
Fuser thermistor |
| E542 |
Fuser temperature too low |
| E543 |
Fuser temperature too high |
| E544 |
Fuser temperature too high |
| E547 |
Fuser lamp won't shut off |
| E548 |
Fuser temperature too high or too low |
| E620 |
Communication problem between main board and ARDF |
| E621 |
Communication problem between main board and sorter |
| E623 |
Communication problem between main board and paper trays |
| E720 |
Sorter stapler timing roller sensor |
| E721 |
Sorter stapler bin lift sensor |
| E722 |
Sorter stapler jogger sensor |
| E723 |
Sorter stapler grip sensor |
| E724 |
Sorter stapler error |
| E900, 901 |
Copy counter |
| U2 |
Key counter |
| U6 |
Fuser unit not installed properly |
| U7 |
Duplex unit |
Ricoh 6080,
6085
| Код ошибки |
Описание |
| 1 |
Exposure lamp |
| 10 |
Scanner velocity |
| 11 |
Scanner return |
| 12 |
Total counter |
| 13 |
Corona problem |
| 2 |
Drum thermistor |
| 3 |
Drum heater |
| 4 |
Drum overheat |
| 5 |
Fuser thermistor |
| 6 |
Fuser lamp |
| 7 |
Fuser overheat |
| 8 |
Optics encoder |
| 9 |
Scanner home |
Ricoh
6620
| Код ошибки |
Описание |
| 11 |
Exposure lamp |
| 12 |
Exposure lamp stays on |
| 21, 22 |
Scan not home |
| 23 |
So signal from registration switch |
| 24 |
Scan not home |
| 25 |
Scan |
| 28 |
Lens not home |
| 29 |
Lens won't leave home |
| 2A |
Second scan sensor |
| 2A |
Mirror sensor stays actuated |
| 2B |
Scan sensor |
| 2C |
Scanner moving to fast |
| 2D |
Scanner moving too slowly or not moving |
| 31 |
Drum thermistor |
| 32 |
Toner sensor |
| 41 |
Third cassette lift motor sensor |
| 52 |
Fuser thermofuse |
| 53 |
Fuser thermistor |
| 54 |
Low temperature at warm up |
| 55 |
High temperature at warm up |
| 56 |
Low temperature after warm up |
| 61 |
Pulse generator |
| 81, 82 |
Duplex jogger |
| 91 |
Counter |
| 93 |
Main board |
Ricoh 6645,
6655, 6665
| Код ошибки |
Описание |
| 101 |
Exposure lamp |
| 103 |
Power frequency problem |
| 104 |
Exposure lamp |
| 120 |
Scanner home problem |
| 121 |
Scan home problem |
| 125 |
Scanning too slow |
| 126 |
Scanning too fast |
| 127 |
Scan drive problem or encoder |
| 140 |
Lens home problem (vertical) |
| 141 |
Lens home problem (vertical) |
| 142 |
Lens home problem (horizontal) |
| 143 |
Lens home problem (horizontal) |
| 144 |
3rd scan sensor problem |
| 145 |
3rd scan sensor problem |
| 146 |
Magnification problem |
| 190 |
Optics thermistor open circuit |
| 191 |
Scan motor thermistor |
| 302 |
Charge corona short |
| 303 |
Charge corona cleaner problem |
| 341 |
Developer motor drive problem |
| 342 |
Toner disposal motor drive problem |
| 343 |
Vsp. Problem. Image density sensor problem |
| 351 |
Vsg. Problem. Higher than 4.3 volts. Image density sensor
problem |
| 352 |
Toner sensor problem during developer calibration |
| 353 |
Vsp Problem. Image density sensor, drum bias or HVT |
| 354 |
Vsg Problem. Image density sensor, drum bias or HVT |
| 355 |
Toner density sensor problem. Vtd problem. Undertoned |
| 356 |
Toner density sensor problem. Vtd problem. Overtoned |
| 357 |
Vsp problem. Image density sensor, drum |
| 358 |
Vsp problem. Image density sensor, drum, toner dust |
| 361 |
Drum potential sensor calibration during process control
setup |
| 364 |
Vd problem. Drum potential sensor, drum or charge corona |
| 365 |
V1 problem. Drum potential sensor, drum, charge corona, dirty
optics |
| 402 |
Transfer, transfer belt, HVT |
| 440 |
Main motor speed problem |
| 442 |
Drum thermistor |
| 500 |
Bypass feed |
| 501 |
Paper feed motor |
| 502 |
1st lift motor |
| 503 |
2nd lift motor |
| 504 |
3rd lift motor |
| 506 |
LCT motor |
| 507 |
LCT feed motor |
| 508 |
Tandem fence motor |
| 510 |
Tandem side home sensor |
| 511 |
Tandem side home sensor |
| 520 |
Duplex/fuser drive motor problem |
| 522 |
Jogger home sensor |
| 523 |
Jogger home sensor |
| 541 |
Fuser thermistor |
| 542 |
Fuser does not warm-up |
| 543 |
Fuser temperature too high. Monitored by main board |
| 544 |
Fuser temperature too high. Monitored by optics board |
| 545 |
Low fuser temperature. Monitored by main board |
| 546 |
Low fuser temperature. Monitored by optics board |
| 547 |
Fuser lamp won't shut off |
| 548 |
Erratic fuser temperature |
| 600 |
Communication problem between main board and operation
board |
| 601 |
Communication problem between main board and optics board |
| 602 |
Communication problem between main board and high voltage
unit |
| 603 |
Main board problem |
| 620 |
Communication problem between main board and document feeder
boards |
| 621 |
Communication problem between main board and sorter staplers or
finisher |
| 700 |
DJF/RDH feed motor |
| 701 |
DJF/RDH transport belt problem |
| 702 |
DJF exit or RDH inverter motor |
| 703 |
RDH exit motor problem |
| 730 |
Sorter/stapler or finisher transport motor |
| 731 |
Bin lift motor |
| 732 |
Tray shift motor |
| 733 |
Tray shift lift motor |
| 735 |
Duplex jogger motor |
| 737 |
Gripper motor |
| 738 |
Staple motor |
| 740 |
Staple drive motor |
| 741 |
Bin rear plate motor (stapler) |
| 742 |
Finisher stack feed motor |
| 900 |
Total counter |
| 901 |
Total counter |
| SC |
Full waste toner bottle. Technician must empty this. Emptying
the waste toner and reinstalling the bottle will clear this
code |
Ricoh 6750
| Код ошибки |
Описание |
| 11 |
Exposure lamp |
| 13 |
Exposure lamp |
| 14 |
Electrical frequency problem |
| 21, 22 |
Scan problem |
| 24 |
Scan home problem |
| 25 |
Scan drive motor problem |
| 26 |
Scan problem during simulation V1 adjustment (SP mode 67) |
| 27 |
Scan problem during simulation |
| 28, 29 |
Lens home problem |
| 2A, 2B |
Mirror home sensor |
| 2D |
Scan drive problem or fuse 5 on optics board |
| 31 |
Drum thermistor |
| 41 |
Tray lift |
| 42 |
2nd tray lift |
| 43 |
3rd tray lift |
| 53 |
Fuser thermistor problem |
| 54 |
Fuse temperature low |
| 55 |
Fuser temperature too high |
| 56 |
Fuser temperature low |
| 57 |
Fuser lamp on too long |
| 58 |
Fuser temperature erratic |
| 61 |
Main drive problem, or fuse 1 or fuse 6 on main motor
board |
| 62 |
Developer drive problem, or fuse 1 on developer motor drive
board |
| 81, 82 |
Duplex jogger home sensor |
| 85, 86 |
Charge corona cleaner problem |
| 87 |
Transfer/separator corona cleaner unit not working |
| 88 |
Transfer/separator corona cleaner unit not home |
| 91 |
Total counter |
| B1 |
Sorter shift tray |
| B2 |
Sorter shift motor |
| B3 |
Sorter shift tray up/down motor |
| B4 |
Stapler transport motor |
| B5 |
Stapler lift motor |
| B6 |
Stapler drive motor |
| B7 |
Stapler jogger motor |
| B8 |
Stapler motor |
Ricoh
M10
| Код ошибки |
Описание |
| E1 |
Exposure lamp |
| E2 |
Scan |
| E5 |
Fuser |
| E6 |
Drive |
| E7 |
Master not turning |
| E8 |
Lamp heater (exposure) |
Gestetner 2217ZD
| Код ошибки |
Описание |
| C2 |
Drive problem |
| C3 |
Scan problem |
| C4 |
Lens problem |
| C5 |
Coronas |
| C6 |
Heater problem or only 1 of the 2 front door interlocks switches
is actuated |
| CO |
Main board problem Run simulation 90. Try power
off/on |
Вы находитесь: Главная
|
Ремонт принтеров
