|
Мы осуществляем ремонт принтеров следующих производителей:
|
| |
|
|
QR-Код:  |
| |
|
| |
Коды ошибок аналоговых
копировальных аппаратов Sharp
Если Ваш аналоговый копировальный аппарат Sharp выдал на
индикации некий код, то узнать причину возникновения ошибки Вы можете в
этом разделе.
Но код ошибки - это лишь следствие сбоя в работе аппарата
Sharp 1420, 1430
| Код ошибки |
Описание |
| A1 |
Jam in document feeder |
| A2 |
Jam in document feeder |
| C1 |
Cassette misfeed |
| C2 |
Cassette feed, bypass unplugged |
| C3 |
Bypass misfeed |
| E1 |
Paper feed jam |
| E3 |
Exit jam |
| EE-EL |
Developer overtoned during setup |
| EE-EU |
Developer undertoned during setup |
| J0 |
Developer setup taking place |
| J1 |
Add toner |
| J3 |
Drum unit not installed properly or missing |
| J7 |
Drum unit due for replacing |
| J8 |
Wrong drum unit or power was turned on after J7 displayed |
| L6 |
Key counter or other optional counter accessory problem |
| U1 |
Drive problem |
| U2 |
Scan |
| U3 |
Lens |
| U4-01 |
Fuser thermistor |
| U4-02 |
High fuser temperature |
| U4-03 |
Low fuser temperature |
| U5 |
500 sheet cassette lift motor |
| U6 |
Main board problem |
| U7 |
Document glass too hot (with document feeder) |
| U8 |
Problem with line voltage |
| U9 |
Auto developer setup problem |
Sharp 2014
| Код ошибки |
Описание |
| A1 |
Jam in document feeder |
| A2 |
Jam in document feeder |
| C1 |
Cassette misfeed |
| C2 |
Cassette feed, bypass unplugged |
| C3 |
Bypass misfeed |
| E1 |
Paper feed jam |
| E3 |
Exit jam |
| EE-EL |
Developer overtoned during setup |
| EE-EU |
Developer undertoned during setup |
| J0 |
Developer setup taking place |
| J1 |
Add toner |
| J3 |
Drum unit not installed properly or missing |
| J7 |
Drum unit due for replacing |
| J8 |
Wrong drum unit or power was turned on after J7 displayed |
| L6 |
Key counter or other optional counter accessory problem |
| U1 |
Drive problem |
| U2 |
Scan |
| U3 |
Lens |
| U4-01 |
Fuser thermistor |
| U4-02 |
High fuser temperature |
| U4-03 |
Low fuser temperature |
| U5 |
500 sheet cassette lift motor |
| U6 |
Main board problem |
| U7 |
Document glass too hot (with document feeder) |
| U8 |
Problem with line voltage |
| U9 |
Auto developer setup problem |
Sharp 2020
| Код ошибки |
Описание |
| CC |
Original detection problem |
| CH |
Lit Steadily: Sorter not installed, or not turned on |
| CH |
Flashing: DV unit not installed, not connected properly, or not
latched in place properly |
| F1 |
Sub code 00: Communication error between main board and sorter.
Sub code 02: Sorter transport motor drive. |
| F2 |
Sub code 31: Image density sensor. Could be a problem with light
level. Sub code 32: Drum mark sensor problem. . Does not see mark on
drum or sensor not working properly. |
| H2 |
Sub code 00: Fuser thermistor open. |
| H3 |
Sub code 00: Fuser temperature too high. |
| H4 |
Sub code 00: Fuser temperature too low. Lamp, thermal switch,
connections. |
| L1 |
Scan forward problem. Motor, sensor, board |
| L3 |
Scan forward problem. Motor, sensor, board. |
| L4 |
Drive problem; main motor, gear, sensor, bind. |
| L5 |
Lens problem. Motor sensor board. |
| L8 |
Sub code 01: Zero cross. |
| P |
Paper feed problem or no paper |
| PC |
Card counter not installed |
| U2 |
Sub code 01: Memory loss. |
| U4 |
Sub code 00: Communication problem between copier and duplex
unit. |
| U5 |
Sub code 00: Communication problem between main board and
ADF. |
Sharp 2022, 2027,
2035
| Код ошибки |
Описание |
| P10 |
Set or clear departmental counter |
| P11 |
Display individual departmental counts |
| P13 |
Clear departmental counters |
| P14 |
Enter, clear or change department numbers |
| P16 |
Change max. number of copies that can be run |
| P18 |
Sends alarm if the wrong department number is tried three times
in a row |
| P19 |
Change code number |
| P20 |
Adjust auto exposure |
| P21 |
Adjust automautic shufoff |
| P22 |
Adjust manual exposure |
| P23 |
Adjust auto clear time |
| P24 |
Set up fixed magnification settings |
| P25 |
Set maximum number of copies or of sets |
| P26 |
Binding margin |
| P27 |
Border erase setting |
| P28 |
Defaults at power on |
| P29 |
Display various counts |
| P30 |
Auto repeat on or off |
| P45 |
Message display time |
| P70 |
Auto paper select on or off |
| P71 |
Auto cassette select on or off |
| P72 |
Maximum copies in duplex |
| P73 |
Copy condition in rewrite |
| P74 |
Duplex limit when problems with duplex unit |
| P75 |
Prevent auto duplex |
| P76 |
Prevent stapling |
| P77 |
Prevent cover use |
| P90 |
List programs |
Sharp 2025,
2030, 2040
| Код ошибки |
Описание |
| C2 |
Transfer corona problem or HVT |
| CC |
Original detection problem. |
| CH |
Door open or developer unit not installed, not connected
properly, or not latched in place properly. |
| F1 |
Sub code 00: Communication error between main board and sorter.
01: Jogger error. 02: Sorter transport motor drive. 04: Sorter bin
sensor problem. Lower limit sensed wrong. |
| F2 |
Sub code 02: Toner motor problem. 31: Image density sensor
problem. Could be a problem with the light level. 32: Drum mark
sensor problem. Does not see mark on drum or sensor does not work
properly. 35: Grid voltage correction will not work during
simulation. |
| F3 |
Sub code 12: Copier upper cassette lift motor problem. Copier
bottom cassette lift motor problem. |
| H2 |
Fuser thermistor open. |
| H3 |
Fuser temperature too high. |
| H4 |
Fuser temperature too low. Lamp, thermal switch,
connections. |
| L4 |
Sub code 01: Drive problem, main motor, sensor, bind. |
| L5 |
Sub code 03: Drive problem with 4th/5th mirror assembly, motor,
sensor, board. |
| L8 |
Sub code 01: Power frequency problem. |
| PC |
Card counter or key counter not installed. |
| PF |
There is an inhibit command from the PC modem. This is reset
with simulation 17. |
| U2 |
Sub code 00 or 01: Memory error. |
| U3 |
Sub code 20: Mirror motor locked. 21: Mirror motor home
sensor. |
| U4 |
Sub code 02: Duplex alignment plate out of position motor,
cable, sensor. |
| U5 |
Sub code 00: Communication problem between main board and RADF.
01: RADF motor drive problem. 02: RADF motor drive problem. 03: RADF
resist sensor. 04: RADF exit sensor. |
| U6 |
Sub code 00: Communication error between copier and desk. 01,
02, 03: Desk lift motor drive problem. 08: Desk 24v problem. 09: LCT
motor overload. 10: Desk transport motor drive problem. |
| U7 |
Sub code 00: Communication problem between copier and PC
modem. |
Sharp 2050
| Код ошибки |
Описание |
| CC-nn |
Original sensing problem |
| CH |
Lit steadily: Door open |
| CH |
Flashing: Developer unit not installed, not latched or not
installed properly |
| EE-EL |
During developer calibration, overtoned condition detected |
| EE-EU |
During developer calibration, undertoned condition
detected |
| F1-00 |
Communication problem between main board and stapler |
| F1-02 |
Stapler sorter transport drive problem |
| F1-03 |
Problem with guide bar oscillator motor |
| F1-04 |
Index lower sensor |
| F1-05 |
Index upper sensor |
| F1-06 |
Shift motor problem in stapler sorter, or index motor
problem |
| F1-08 |
Staple sorter shift motor drive problem |
| F1-10 |
Stapler problem |
| F2-00 |
Toner sensor problem |
| F2-31 |
Drum surface reflecting problem |
| F2-32 |
Drum sensor not scanning mark properly |
| F2-33 |
Grid voltage is too high or too low |
| F2-35 |
During patch detection, measurement is wrong |
| F2-37 |
Drum mark sensor adjustment problem |
| F3-01 |
LCT encoder |
| F3-02 |
LCT lift problem |
| F3-03 |
LCT down problem |
| F3-12 |
Cassette 1 lift problem |
| F3-22 |
Cassette 2 lift problem |
| F3-32 |
Cassette 3 lift problem |
| F3-42 |
Cassette 4 lift problem |
| H2-00 |
Fuser thermistor |
| H3-00 |
Fuser temperature too high |
| H4-00 |
Fuser temperature too low |
| L1-00 |
Scan problem |
| L2-00 |
Mirror motor drive problem |
| L3-00 |
Scan return problem |
| L4-01 |
Drum motor drive problem |
| L4-02 |
Main motor drive problem |
| L5-00 |
4/5 mirror drive problem |
| L8-01 |
Full wave signal missing to auto exposure |
| L8-02 |
Full wave signal to auto exposure is incorrect |
| L8-03 |
During auto exposure adjust procedure, the auto exp. |
| P20 |
Adjust automatic exposure |
| P21 |
Auto shut off timing |
| P22 |
Toner save mode |
| P25 |
Maximum number of copies that can be selected |
| P26 |
Margin shift |
| P28 |
Initial status |
| P29 |
To read total copies |
| P70 |
Auto paper select |
| P72 |
Bypass in duplex |
| P74 |
Stop document feeder use |
| P75 |
Stop duplex use |
| P76 |
Stop stapler use |
| P83 |
Modem access to codes through phone line |
| P90 |
Display all of the operator programs |
| PC |
Card counter |
| PF |
Modem problem |
| U0-00 |
Operation panel problem |
| U2-00 |
EEPROM error. Reset with sim. 16 |
| U3-00 |
Communication problem between master and mirror controller |
| U3-20 |
Mirror drive problem |
| U3-21 |
Mirror home sensor problem |
| U3-26 |
Mirror motor voltage problem |
| U3-41 |
Lens motor home correction did not go well |
| U3-42 |
4/5 mirror motor problem similar to U3 -41 |
| U4-02 |
Duplex alignment plate sensor |
| U4-03 |
Duplex rear plate sensor |
| U5-00 |
Communication problem between RADF and copier |
| U5-01 |
RADF resist sensor |
| U5-02 |
RADF reverse sensor |
| U5-03 |
RADF timing sensor |
| U5-04 |
RADF empty sensor |
| U5-11 |
RADF paper feed drive problem |
| U5-12 |
RADF transport drive problem |
| U7-00 |
Communication problem between copier and
modem |
Sharp 2114
| Код ошибки |
Описание |
| A1 |
Jam in document feeder |
| A2 |
Jam in document feeder |
| C1 |
Cassette misfeed |
| C2 |
Cassette feed, bypass unplugged |
| C3 |
Bypass misfeed |
| E1 |
Paper feed jam |
| E3 |
Exit jam |
| EE-EL |
Developer overtoned during setup |
| EE-EU |
Developer undertoned during setup |
| J0 |
Developer setup taking place |
| J1 |
Add toner |
| J3 |
Drum unit not installed properly or missing |
| J7 |
Drum unit due for replacing |
| J8 |
Wrong drum unit or power was turned on after J7 displayed |
| L6 |
Key counter or other optional counter accessory problem |
| U1 |
Drive problem |
| U2 |
Scan |
| U3 |
Lens |
| U4-01 |
Fuser thermistor |
| U4-02 |
High fuser temperature |
| U4-03 |
Low fuser temperature |
| U5 |
500 sheet cassette lift motor |
| U6 |
Main board problem |
| U7 |
Document glass too hot (with document feeder) |
| U8 |
Problem with line voltage |
| U9 |
Auto developer setup problem |
Sharp 2116, 2118
| Код ошибки |
Описание |
| CH |
Flashing: DV unit not installed, not connected properly |
| CH |
Lit steadily: Sorter not installed or not turned on |
| EE-EL |
During developer calibration, problem of some kind. Over
toned |
| EE-EU |
During developer calibration, problem of some kind. Under
toned |
| F1-00 |
Communication error between main board and sorter |
| F1-02 |
Transport motor drive |
| F1-04 |
Bin sensor problem. Upper or lower limit sensor problem |
| F1-05 |
Sorter bin home sensor |
| F1-06 |
Sorter bin motor drive |
| F1-14 |
Take out sensor problem |
| F2-31 |
Image density sensor problem |
| F2-32 |
Drum mark sensor problem |
| F2-35 |
Grid voltage correction will not work on the patch voltage is
outside the expected range |
| H2-00 |
Fuser thermistor open |
| H3-00 |
Fuser temperature too high |
| H4-00 |
Fuser temperature too low. Lamp, thermal switch,
connections |
| L1 |
Scan forward problem |
| L3 |
Scan return problem |
| L4 |
Drive problem; main motor, gear, sensor, bind |
| L5 |
Lens problem |
| L8-01 |
Zero cross (board problem) |
| L8-03 |
Auto exposure sensor problem |
| P |
Paper feed problem |
| PC |
Card counter not installed |
| U2-01 |
Memory loss |
| U2-04 |
EEPROM error |
| U5-00 |
Communication problem between main board and ADF |
| U5-01 |
Registration sensor problem during adjustment, or adjustment
value is not a valid number |
| U5-02 |
Exit sensor adjustment problem; invalid adjustment value |
| U5-11 |
Paper feed drive problem |
| U5-12 |
Transport motor drive |
Sharp
2120, 2216
| Код ошибки |
Описание |
| CC |
Original detection problem |
| CH |
Lit Steadily: Sorter not installed, or not turned on |
| CH |
Flashing: DV unit not installed, not connected properly, or not
latched in place properly |
| F1 |
Sub code 00: Communication error between main board and sorter.
Sub code 02: Sorter transport motor drive. |
| F2 |
Sub code 31: Image density sensor. Could be a problem with light
level. Sub code 32: Drum mark sensor problem. Does not see mark on
drum or sensor not working properly. |
| H2 |
Sub code 00: Fuser thermistor open. |
| H3 |
Sub code 00: Fuser temperature too high. |
| H4 |
Sub code 00: Fuser temperature too low. Lamp, thermal switch,
connections. |
| L1 |
Scan forward problem. Motor, sensor, board |
| L3 |
Scan forward problem. Motor, sensor, board. |
| L4 |
Drive problem; main motor, gear, sensor, bind. |
| L5 |
Lens problem. Motor sensor board. |
| L8 |
Sub code 01: Zero cross. |
| P |
Paper feed problem or no paper |
| PC |
Card counter not installed |
| U2 |
Sub code 01: Memory loss. |
| U4 |
Sub code 00: Communication problem between copier and duplex
unit. |
| U5 |
Sub code 00: Communication problem between main board and
ADF. |
Sharp 2214
| Код ошибки |
Описание |
| A1 |
Jam in document feeder |
| A2 |
Jam in document feeder |
| C1 |
Cassette misfeed |
| C2 |
Cassette feed, bypass unplugged |
| C3 |
Bypass misfeed |
| E1 |
Paper feed jam |
| E3 |
Exit jam |
| EE-EL |
Developer overtoned during setup |
| EE-EU |
Developer undertoned during setup |
| J0 |
Developer setup taking place |
| J1 |
Add toner |
| J3 |
Drum unit not installed properly or missing |
| J7 |
Drum unit due for replacing |
| J8 |
Wrong drum unit or power was turned on after J7 displayed |
| L6 |
Key counter or other optional counter accessory problem |
| U1 |
Drive problem |
| U2 |
Scan |
| U3 |
Lens |
| U4-01 |
Fuser thermistor |
| U4-02 |
High fuser temperature |
| U4-03 |
Low fuser temperature |
| U5 |
500 sheet cassette lift motor |
| U6 |
Main board problem |
| U7 |
Document glass too hot (with document feeder) |
| U8 |
Problem with line voltage |
| U9 |
Auto developer setup problem |
Sharp 2314
| Код ошибки |
Описание |
| CH |
If lit steadily, paper feed section cover is open or manual feed
unit not installed properly. If flashing, developer seal still
installed, or toner density sensor/main board problem. |
| EE |
Sub code EU: undertoned. May be toner density sensor problem or
developer unit problem.
Sub code EL: Over toned. May be toner
density sensor problem or developer unit problem. |
| H2 |
Sub code 0: Fuser thermistor. |
| H3 |
Sub code 0: Fuser temperature too high. |
| H4 |
Sub code 0: Fuser temperature too low. |
| L1 |
Scan problem. Sub code is 0, but there is no more detail. Could
be no scan drive; scan did not leave home; scan did not return home;
scan overloaded; mirror motor problem; scan cable came off. |
| L3 |
Scan return problem. Sub code 0. Approximately same causes as
L1 |
| L4 |
Sub code 1: Main drive problem. Sensor, gear, motor. |
| L5 |
Sub code 2: Lens drive, motor, sensor. |
| L8 |
Sub code 1: Power frequency varies by more than 5 % or for more
than 5 sec. Sub code 3: AE sensor problem. |
| PC |
Key counter not installed. |
| SPFJAM |
Document feeder problem. |
| U2 |
Sub code 1: Main board EEPROM problem. Sub code 4: Memory
problem. |
| U5 |
Sub code 5: high temperature at exposure glass when using
document feeder. |
Sharp 2414,
2514
| Код ошибки |
Описание |
| CH |
If lit steadily, paper feed section cover is open or manual feed
unit not installed properly. If flashing, developer seal still
installed, or toner density sensor/main board problem. |
| EE |
Sub code EU: undertoned. May be toner density sensor problem or
developer unit problem. Sub code EL: Over toned. May be toner
density sensor problem or developer unit problem. |
| H2 |
Sub code 0: Fuser thermistor. |
| H3 |
Sub code 0: Fuser temperature too high. |
| H4 |
Sub code 0: Fuser temperature too low. |
| L1 |
Scan problem. Sub code is 0, but there is no more detail. Could
be no scan drive; scan did not leave home; scan did not return home;
scan overloaded; mirror motor problem; scan cable came off. |
| L3 |
Scan return problem. Sub code 0. Approximately same causes as
L1 |
| L4 |
Sub code 1: Main drive problem. Sensor, gear, motor. |
| L5 |
Sub code 2: Lens drive, motor, sensor. |
| L8 |
Sub code 1 Power frequency varies by more than 5 % or for more
than 5 sec. Sub code 3: AE sensor problem. |
| PC |
Key counter not installed. |
| SPFJAM |
Document feeder problem. |
| U2 |
Sub code 1: Main board EEPROM problem. Sub code 4: Memory
problem. |
| U5 |
Sub code 5: high temperature at exposure glass when using
document feeder |
Sharp 7100,
7200
| Код ошибки |
Описание |
| 0 |
Stepping motor |
| 10 |
Mirror motor |
| 40 |
Dark box switch |
| 8 |
Mirror motor |
| C1 |
Charge corona |
| C2 |
Transfer corona |
| C3 |
Discharge corona |
| CH |
possible DV unit not installed properly |
| CH |
Interlock or thermal fuse |
| H1 |
Heater thermal fuse |
| H2 |
Thermistor |
| H3 |
High Temperature |
| H4 |
Low Temperature |
| H5 |
Lower thermofuse |
| H6 |
Lower thermistor |
| H7 |
High temperature in lower roller |
| H8 |
Low temperature in lower roller |
| L1 |
Forward Scan |
| L2 |
End of Scan |
| L3 |
Return of Scan |
| L4 |
PT/main motor |
| L5 |
Lens |
| P1 |
Copy lamp thermal fuse |
| U1 |
Low battery |
| U2 |
Data transfer |
| U3 |
Dark box |
Sharp 7320,
7370
| Код ошибки |
Описание |
| CH |
Door open or developer unit out |
| EL |
Developer problem |
| EU |
Developer set up problem |
| P flashing |
Out of paper |
| P lit |
No cassette in machine |
| PC |
Personal counter not installed |
| U3 |
Auto exposure sensor problem |
Sharp 750
| Код ошибки |
Описание |
| 0 |
Stepping motor |
| 10 |
Mirror motor |
| 40 |
Dark box switch |
| 8 |
Mirror motor |
| C1 |
Charge corona |
| C2 |
Transfer corona |
| C3 |
Discharge corona |
| CH |
Interlock or thermal fuse |
| CH |
possible DV unit not installed properly |
| H1 |
Heater thermal fuse |
| H2 |
Thermistor |
| H3 |
High Temperature |
| H4 |
Low Temperature |
| H5 |
Lower thermofuse |
| H6 |
Lower thermistor |
| H7 |
High temperature in lower roller |
| H8 |
Low temperature in lower roller |
| L1 |
Forward Scan |
| L2 |
End of Scan |
| L3 |
Return of Scan |
| L4 |
PT/main motor |
| L5 |
Lens |
| P1 |
Copy lamp thermal fuse |
| U1 |
Low battery |
| U2 |
Data transfer |
| U3 |
Dark box |
SERVICE TIPS & PROCEDURES. Maintenance
Counter reset is CROP 20, Print
General reset for error codes is
CROP 14, Print |
Sharp 755, 756,
760
| Код ошибки |
Описание |
| 0 |
Stepping motor |
| 10 |
Mirror motor |
| 40 |
Dark box switch |
| 8 |
Mirror motor |
| C1 |
Charge corona |
| C2 |
Transfer corona |
| C3 |
Discharge corona |
| CH |
possible DV unit not installed properly |
| CH |
Interlock or thermal fuse |
| H1 |
Heater thermal fuse |
| H2 |
Thermistor |
| H3 |
High Temperature |
| H4 |
Low Temperature |
| H5 |
Lower thermofuse |
| H6 |
Lower thermistor |
| H7 |
High temperature in lower roller |
| H8 |
Low temperature in lower roller |
| L1 |
Forward Scan |
| L2 |
End of Scan |
| L3 |
Return of Scan |
| L4 |
PT/main motor |
| L5 |
Lens |
| P1 |
Copy lamp thermal fuse |
| U1 |
Low battery |
| U2 |
Data transfer |
| U3 |
Dark box |
Sharp 770
| Код ошибки |
Описание |
| 0 |
Stepping motor |
| 10 |
Mirror motor |
| 40 |
Dark box switch |
| 8 |
Mirror motor |
| C1 |
Charge corona |
| C2 |
Transfer corona |
| C3 |
Discharge corona |
| CH |
possible DV unit not installed properly |
| CH |
Interlock or thermal fuse |
| H1 |
Heater thermal fuse |
| H2 |
Thermistor |
| H3 |
High Temperature |
| H4 |
Low Temperature |
| H5 |
Lower thermofuse |
| H6 |
Lower thermistor |
| H7 |
High temperature in lower roller |
| H8 |
Low temperature in lower roller |
| L1 |
Forward Scan |
| L2 |
End of Scan |
| L3 |
Return of Scan |
| L4 |
PT/main motor |
| L5 |
Lens |
| P1 |
Copy lamp thermal fuse |
| U1 |
Low battery |
| U2 |
Data transfer |
| U3 |
Dark box |
| 0 |
Main board, operations panel |
| 0 |
Data transfer (main and operations) |
| 0 |
Data transfer (main and ADF) |
| 1 |
Document feeded motors |
| 1 |
Exposure lamp board or operations |
| 2 |
Automatic exposure sensor, exposure lamp board |
| U |
Press {Print} and read secondary code: |
| U3 |
Press {Print} and read secondary code: |
| U4 |
Press {Print} and read secondary
code: |
Sharp 7700, 7750
| Код ошибки |
Описание |
| 0 |
Data transfer (main and ADF) |
| 0 |
Data transfer (main and operations) |
| 0 |
Main board, operations panel |
| 1 |
Document feeded motors |
| 1 |
Exposure lamp board or operations |
| 2 |
Automatic exposure sensor, exposure lamp board |
| U |
Press {Print} and read secondary code: |
| U3 |
Press {Print} and read secondary code: |
| U4 |
Press {Print} and read secondary
code: |
Sharp 771
| Код ошибки |
Описание |
| 0 |
Stepping motor |
| 10 |
Mirror motor |
| 40 |
Dark box switch |
| 8 |
Mirror motor |
| C1 |
Charge corona |
| C2 |
Transfer corona |
| C3 |
Discharge corona |
| CH |
possible DV unit not installed properly |
| CH |
Interlock or thermal fuse |
| H1 |
Heater thermal fuse |
| H2 |
Thermistor |
| H3 |
High Temperature |
| H4 |
Low Temperature |
| H5 |
Lower thermofuse |
| H6 |
Lower thermistor |
| H7 |
High temperature in lower roller |
| H8 |
Low temperature in lower roller |
| L1 |
Forward Scan |
| L2 |
End of Scan |
| L3 |
Return of Scan |
| L4 |
PT/main motor |
| L5 |
Lens |
| P1 |
Copy lamp thermal fuse |
| U1 |
Low battery |
| U2 |
Data transfer |
| U3 |
Dark box |
Sharp 780
| Код ошибки |
Описание |
| 0 |
Stepping motor |
| 10 |
Mirror motor |
| 40 |
Dark box switch |
| 8 |
Mirror motor |
| C1 |
Charge corona |
| C2 |
Transfer corona |
| C3 |
Discharge corona |
| CH |
Interlock or thermal fuse |
| CH |
possible DV unit not installed properly |
| H1 |
Heater thermal fuse |
| H2 |
Thermistor |
| H3 |
High Temperature |
| H4 |
Low Temperature |
| H5 |
Lower thermofuse |
| H6 |
Lower thermistor |
| H7 |
High temperature in lower roller |
| H8 |
Low temperature in lower roller |
| L1 |
Forward Scan |
| L2 |
End of Scan |
| L3 |
Return of Scan |
| L4 |
PT/main motor |
| L5 |
Lens |
| P1 |
Copy lamp thermal fuse |
| U1 |
Low battery |
| U2 |
Data transfer |
| U3 |
Dark box |
| CC |
Document sensor |
| CH |
Door open |
| EE |
Developer did not set up properly |
| EL |
Developer sensor |
| EU |
Developer sensor |
| H2 |
Thermistor |
| H3 |
High temperature |
| H4 |
Low temperature |
| L1 |
Forward scan |
| L2 |
Forward scan |
| L3 |
Scan return |
| L5 |
Lens |
| L6 |
Bottom rotating cassette |
| L8 |
Signal |
| L9 |
Sorter |
| U1 |
Battery |
| U2 |
Back up battery |
| U3 |
Auto exposure sensor |
| U5 |
Problem in interface between machine and
ADF |
Sharp 7800
| Код ошибки |
Описание |
| CC |
Document sensor |
| CH |
Door open |
| EE |
Developer did not set up properly |
| EL |
Developer sensor |
| EU |
Developer sensor |
| H2 |
Thermistor |
| H3 |
High temperature |
| H4 |
Low temperature |
| L1 |
Forward scan |
| L2 |
Forward scan |
| L3 |
Scan return |
| L5 |
Lens |
| L6 |
Bottom rotating cassette |
| L8 |
Signal |
| L9 |
Sorter |
| U1 |
Battery |
| U2 |
Back up battery |
| U3 |
Auto exposure sensor |
| U5 |
Problem in interface between machine and
ADF |
Sharp 781
| Код ошибки |
Описание |
| 0 |
Stepping motor |
| 10 |
Mirror motor |
| 40 |
Dark box switch |
| 8 |
Mirror motor |
| C1 |
Charge corona |
| C2 |
Transfer corona |
| C3 |
Discharge corona |
| CH |
possible DV unit not installed properly |
| CH |
Interlock or thermal fuse |
| H1 |
Heater thermal fuse |
| H2 |
Thermistor |
| H3 |
High Temperature |
| H4 |
Low Temperature |
| H5 |
Lower thermofuse |
| H6 |
Lower thermistor |
| H7 |
High temperature in lower roller |
| H8 |
Low temperature in lower roller |
| L1 |
Forward Scan |
| L2 |
End of Scan |
| L3 |
Return of Scan |
| L4 |
PT/main motor |
| L5 |
Lens |
| L6 |
Charge block switch |
| P1 |
Copy lamp thermal fuse |
| U1 |
Low battery |
| U2 |
Data transfer |
| U3 |
Dark box |
Sharp 7850
| Код ошибки |
Описание |
| CC |
Document sensor |
| CH |
Door open |
| EE |
Developer did not set up properly |
| EL |
Developer sensor |
| EU |
Developer sensor |
| H2 |
Thermistor |
| H3 |
High temperature |
| H4 |
Low temperature |
| L1 |
Forward scan |
| L2 |
Forward scan |
| L3 |
Scan return |
| L5 |
Lens |
| L6 |
Bottom rotating cassette |
| L8 |
Signal |
| L9 |
Sorter |
| U1 |
Battery |
| U2 |
Back up battery |
| U3 |
Auto exposure sensor |
| U5 |
Problem in interface between machine and
ADF |
Sharp 7900
| Код ошибки |
Описание |
| CC |
Not sensing document on glass |
| CH |
Door open/DV unit not installed properly |
| EE |
DV did not set up properly |
| EL |
DV problem-overtoned condition |
| EU |
DV problem-undertoned condition |
| H2 |
Fuser thermistor |
| H3 |
Fuser temperature too high |
| H4 |
Fuser temperature too low |
| L1 |
Forward scan |
| L3 |
Return scan |
| L7 |
Developer unit shift problem |
| PC |
Key counter |
| U1 |
Dead battery |
| U2 |
Battery problem |
Sharp
810
| Код ошибки |
Описание |
| 1 |
Open interlock switch |
| 2 |
Bad thermofuse/thermistor |
| 3 |
High or low temperature |
| 4 |
Scanner problem |
| 0 |
Data transfer |
| 10 |
Mirror base |
| 4 |
Stepping motor clock pulse |
| 40 |
Lens |
| 8 |
Mirror motor |
| U3 |
Press {Print} and read secondary
code: |
Sharp 8100
| Код ошибки |
Описание |
| 0 |
Data transfer |
| 10 |
Mirror base |
| 4 |
Stepping motor clock pulse |
| 40 |
Lens |
| 8 |
Mirror motor |
| U3 |
Press {Print} and read secondary
code: |
Sharp 811
| Код ошибки |
Описание |
| 1 |
Door or separator interlock |
| 2 |
Instantly=Thermofuse |
| 3 |
High temperature |
| 4 |
Low temperature (if it takes 11 min) |
| 5 |
Scanner problem if it takes several seconds |
| 6 |
Optics problem on 820 |
| 7 |
Thermistor |
Sharp 815
| Код ошибки |
Описание |
| 0 |
Stepping motor |
| 10 |
Mirror motor |
| 40 |
Dark box switch |
| 8 |
Mirror motor |
| C1 |
Charge corona |
| C2 |
Transfer corona |
| C3 |
Discharge corona |
| CH |
possible DV unit not installed properly |
| CH |
Interlock or thermal fuse |
| H1 |
Heater thermal fuse |
| H2 |
Thermistor |
| H3 |
High Temperature |
| H4 |
Low Temperature |
| H5 |
Lower thermofuse |
| H6 |
Lower thermistor |
| H7 |
High temperature in lower roller |
| H8 |
Low temperature in lower roller |
| L1 |
Forward Scan |
| L2 |
End of Scan |
| L3 |
Return of Scan |
| L4 |
PT/main motor |
| L5 |
Lens |
| L6 |
Charge block switch |
| P1 |
Copy lamp thermal fuse |
| U1 |
Low battery |
| U2 |
Data transfer |
| U3 |
Dark box |
Sharp 816
| Код ошибки |
Описание |
| 0 |
Stepping motor |
| 10 |
Mirror motor |
| 40 |
Dark box switch |
| 8 |
Mirror motor |
| C1 |
Charge corona |
| C2 |
Transfer corona |
| C3 |
Discharge corona |
| CH |
Interlock or thermal fuse |
| CH |
possible DV unit not installed properly |
| H1 |
Heater thermal fuse |
| H2 |
Thermistor |
| H3 |
High Temperature |
| H4 |
Low Temperature |
| H5 |
Lower thermofuse |
| H6 |
Lower thermistor |
| H7 |
High temperature in lower roller |
| H8 |
Low temperature in lower roller |
| L1 |
Forward Scan |
| L2 |
End of Scan |
| L3 |
Return of Scan |
| L4 |
PT/main motor |
| L5 |
Lens |
| L6 |
Charge block switch |
| P1 |
Copy lamp thermal fuse |
| U1 |
Low battery |
| U2 |
Data transfer |
| U3 |
Dark box |
Sharp 820
| Код ошибки |
Описание |
| 1 |
Door or separator interlock |
| 2 |
Instantly=Thermofuse |
| 3 |
High temperature |
| 4 |
Low temperature (if it takes 11 min) |
| 5 |
Scanner problem if it takes several seconds |
| 6 |
Optics problem on 820 |
| 7 |
Thermistor |
| A1 |
Document feeder problem. |
| CH |
Toner cartridge not installed or not installed properly. |
| H2 |
Sub code 0: Fuser thermistor. |
| H3 |
Sub code 0: Fuser temperature too high. |
| H4 |
Sub code 0: Fuser temperature too low. |
| L1 |
Document feeder problem. |
| L3 |
Scan return problem. Sub code is 0, but there is no more detail.
Could be no scan drive; scan did not leave home; scan did not return
home; scan overloaded; mirror motor problem; scan cable came
off. |
| L4 |
Sub code 1: Main drive problem. Sensor gear motor. |
| L5 |
Sub code 2: Lens drive, motor, sensor |
| P |
Paper feed. |
| U2 |
Sub code 1: Main board EEPROM problem. 4: Memory problem. |
| U5 |
Sub code 5: high temperature at exposing glass when using
document feeder. |
| 0 |
Stepping motor |
| 10 |
Mirror motor |
| 40 |
Dark box switch |
| 8 |
Mirror motor |
| C1 |
Charge corona |
| C2 |
Transfer corona |
| C3 |
Discharge corona |
| CH |
Interlock or thermal fuse |
| CH |
possible DV unit not installed properly |
| H1 |
Heater thermal fuse |
| H2 |
Thermistor |
| H3 |
High Temperature |
| H4 |
Low Temperature |
| H5 |
Lower thermofuse |
| H6 |
Lower thermistor |
| H7 |
High temperature in lower roller |
| H8 |
Low temperature in lower roller |
| L1 |
Forward Scan |
| L2 |
End of Scan |
| L3 |
Return of Scan |
| L4 |
PT/main motor |
| L5 |
Lens |
| L6 |
Charge block switch |
| P1 |
Copy lamp thermal fuse |
| U1 |
Low battery |
| U2 |
Data transfer |
| U3 |
Dark box |
Sharp 8200
| Код ошибки |
Описание |
| 0 |
Stepping motor |
| 10 |
Mirror motor |
| 40 |
Dark box switch |
| 8 |
Mirror motor |
| C1 |
Charge corona |
| C2 |
Transfer corona |
| C3 |
Discharge corona |
| CH |
Interlock or thermal fuse |
| CH |
possible DV unit not installed properly |
| H1 |
Heater thermal fuse |
| H2 |
Thermistor |
| H3 |
High Temperature |
| H4 |
Low Temperature |
| H5 |
Lower thermofuse |
| H6 |
Lower thermistor |
| H7 |
High temperature in lower roller |
| H8 |
Low temperature in lower roller |
| L1 |
Forward Scan |
| L2 |
End of Scan |
| L3 |
Return of Scan |
| L4 |
PT/main motor |
| L5 |
Lens |
| L6 |
Charge block switch |
| P1 |
Copy lamp thermal fuse |
| U1 |
Low battery |
| U2 |
Data transfer |
| U3 |
Dark box |
Sharp 825
| Код ошибки |
Описание |
| 0 |
Stepping motor |
| 10 |
Mirror motor |
| 40 |
Dark box switch |
| 8 |
Mirror motor |
| A1 |
Document feeder problem. |
| C1 |
Charge corona |
| C2 |
Transfer corona |
| C3 |
Discharge corona |
| CH |
possible DV unit not installed properly |
| CH |
Interlock or thermal fuse |
| CH |
Toner cartridge not installed or not installed properly. |
| H1 |
Heater thermal fuse |
| H2 |
Sub code 0: Fuser thermistor. |
| H2 |
Thermistor |
| H3 |
High Temperature |
| H3 |
Sub code 0: Fuser temperature too high. |
| H4 |
Sub code 0: Fuser temperature too low. |
| H4 |
Low Temperature |
| H5 |
Lower thermofuse |
| H6 |
Lower thermistor |
| H7 |
High temperature in lower roller |
| H8 |
Low temperature in lower roller |
| L1 |
Document feeder problem. |
| L1 |
Forward Scan |
| L2 |
End of Scan |
| L3 |
Return of Scan |
| L3 |
Scan return problem. Sub code is 0, but there is no more detail.
Could be no scan drive; scan did not leave home; scan did not return
home; scan overloaded; mirror motor problem; scan cable came
off. |
| L4 |
PT/main motor |
| L4 |
Sub code 1: Main drive problem. Sensor gear motor. |
| L5 |
Lens |
| L5 |
Sub code 2: Lens drive, motor, sensor |
| L6 |
Charge block switch |
| P |
Paper feed. |
| P1 |
Copy lamp thermal fuse |
| U1 |
Low battery |
| U2 |
Data transfer |
| U2 |
Sub code 1: Main board EEPROM problem. 4: Memory problem. |
| U3 |
Dark box |
| U5 |
Sub code 5: high temperature at exposing glass when using
document feeder. |
Sharp
826
| Код ошибки |
Описание |
| 0 |
Stepping motor |
| 10 |
Mirror motor |
| 40 |
Dark box switch |
| 8 |
Mirror motor |
| C1 |
Charge corona |
| C2 |
Transfer corona |
| C3 |
Discharge corona |
| CH |
Interlock or thermal fuse |
| CH |
possible DV unit not installed properly |
| H1 |
Heater thermal fuse |
| H2 |
Thermistor |
| H3 |
High Temperature |
| H4 |
Low Temperature |
| H5 |
Lower thermofuse |
| H6 |
Lower thermistor |
| H7 |
High temperature in lower roller |
| H8 |
Low temperature in lower roller |
| L1 |
Forward Scan |
| L2 |
End of Scan |
| L3 |
Return of Scan |
| L4 |
PT/main motor |
| L5 |
Lens |
| L6 |
Charge block switch |
| P1 |
Copy lamp thermal fuse |
| U1 |
Low battery |
| U2 |
Data transfer |
| U3 |
Dark box |
Sharp 8260
| Код ошибки |
Описание |
| 0 |
Data transfer |
| 10 |
Mirror base |
| 4 |
Stepping motor clock pulse |
| 40 |
Lens |
| 8 |
Mirror motor |
| U3 |
Press {Print} and read secondary
code: |
Sharp 830, 835
| Код ошибки |
Описание |
| A1 |
Document feeder problem. |
| CH |
Toner cartridge not installed or not installed properly. |
| H2 |
Sub code 0: Fuser thermistor. |
| H3 |
Sub code 0: Fuser temperature too high. |
| H4 |
Sub code 0: Fuser temperature too low. |
| L1 |
Document feeder problem. |
| L3 |
Scan return problem. Sub code is 0, but there is no more detail.
Could be no scan drive; scan did not leave home; scan did not return
home; scan overloaded; mirror motor problem; scan cable came
off. |
| L4 |
Sub code 1: Main drive problem. Sensor gear motor. |
| L5 |
Sub code 2: Lens drive, motor, sensor |
| P |
Paper feed. |
| U2 |
Sub code 1: Main board EEPROM problem. 4: Memory problem. |
| U5 |
Sub code 5: high temperature at exposing glass when using
document feeder. |
| CC |
Not sensing document on glass |
| CH |
Door open/DV unit not installed properly |
| EE |
DV did not set up properly |
| EL |
DV problem-overtoned condition |
| EU |
DV problem-undertoned condition |
| H2 |
Fuser thermistor |
| H3 |
Fuser temperature too high |
| H4 |
Fuser temperature too low |
| L1 |
Forward scan |
| L3 |
Return scan |
| L7 |
Developer unit shift problem |
| PC |
Key counter |
| U1 |
Dead battery |
| U2 |
Battery problem |
Sharp 8300,
8350, 8400
| Код ошибки |
Описание |
| CC |
Not sensing document on glass |
| CH |
Door open/DV unit not installed properly |
| EE |
DV did not set up properly |
| EL |
DV problem-overtoned condition |
| EU |
DV problem-undertoned condition |
| H2 |
Fuser thermistor |
| H3 |
Fuser temperature too high |
| H4 |
Fuser temperature too low |
| L1 |
Forward scan |
| L3 |
Return scan |
| L7 |
Developer unit shift problem |
| PC |
Key counter |
| U1 |
Dead battery |
| U2 |
Battery problem |
Sharp
845
| Код ошибки |
Описание |
| A1 |
Document feeder problem. |
| CH |
Toner cartridge not installed or not installed properly. |
| H2 |
Sub code 0: Fuser thermistor. |
| H3 |
Sub code 0: Fuser temperature too high. |
| H4 |
Sub code 0: Fuser temperature too low. |
| L1 |
Document feeder problem. |
| L3 |
Scan return problem. Sub code is 0, but there is no more detail.
Could be no scan drive; scan did not leave home; scan did not return
home; scan overloaded; mirror motor problem; scan cable came
off. |
| L4 |
Sub code 1: Main drive problem. Sensor gear motor. |
| L5 |
Sub code 2: Lens drive, motor, sensor |
| P |
Paper feed. |
| U2 |
Sub code 1: Main board EEPROM problem. 4: Memory problem. |
| U5 |
Sub code 5: high temperature at exposing glass when using
document feeder. |
Sharp
850
| Код ошибки |
Описание |
| 1 |
Door or separator interlock |
| 2 |
Instantly=Thermofuse |
| 3 |
High temperature |
| 4 |
Low temperature (if it takes 11 min) |
| 5 |
Scanner problem if it takes several seconds |
| 6 |
Optics problem on 820 |
| 7 |
Thermistor |
Sharp
8600
| Код ошибки |
Описание |
| 0 |
Data transfer |
| 10 |
Mirror base |
| 4 |
Stepping motor clock pulse |
| 40 |
Lens |
| 8 |
Mirror motor |
| U3 |
Press {Print} and read secondary
code: |
Sharp 8875
| Код ошибки |
Описание |
| C2 |
Transfer corona problem |
| CH |
If lit steadily, open door or other interlock. If flashing,
developer unit not installed or not connected properly |
| H2 |
Fuser thermistor |
| H3 |
Fuser overheat. Triac pinched wire |
| H4 |
Low fuser temperature. Lamp, thermal fuse, thermistor,
connection |
| L1 |
Scan problem. Did not leave home position |
| L2 |
Scan left home, but did not complete scan |
| L3 |
No return scan |
| L4 |
Drive problem |
| L5 |
Lens problem |
| L9 |
Sorter index. If 0 is flashing, sorter index home sensor did not
actuate. If 1 is flashing, sorter bottom actuator remained
actuated |
| U1 |
Battery. Replace battery (might have 2) and do simulation 13 to
reset |
| U2 |
Communication problem within boards. To reset, jumper test
points W2 & U2 |
Sharp 900,
901
| Код ошибки |
Описание |
| 0 |
Stepping motor |
| 10 |
Mirror motor |
| 40 |
Dark box switch |
| 8 |
Mirror motor |
| C1 |
Charge corona |
| C2 |
Transfer corona |
| C3 |
Discharge corona |
| CH |
possible DV unit not installed properly |
| CH |
Interlock or thermal fuse |
| H1 |
Heater thermal fuse |
| H2 |
Thermistor |
| H3 |
High Temperature |
| H4 |
Low Temperature |
| H5 |
Lower thermofuse |
| H6 |
Lower thermistor |
| H7 |
High temperature in lower roller |
| H8 |
Low temperature in lower roller |
| L1 |
Forward Scan |
| L2 |
End of Scan |
| L3 |
Return of Scan |
| L4 |
PT/main motor |
| L5 |
Lens |
| L6 |
Charge block switch |
| P1 |
Copy lamp thermal fuse |
| U1 |
Low battery |
| U2 |
Data transfer |
| U3 |
Dark box |
Sharp 9300, 9500,
9550
| Код ошибки |
Описание |
| 0 |
Desk board and main board |
| 0 |
Data transfer |
| 10 |
Desk alignment board |
| 10 |
Mirror base |
| 20 |
Sort gate |
| 4 |
Stepping motor clock pulse |
| 40 |
Lens |
| 8 |
Mirror motor |
| U3 |
Press {Print} and read secondary code: |
| U4 |
Press {Print} and read secondary
code: |
Sharp 9700, 9750
| Код ошибки |
Описание |
| 40 |
Flashing - Lens home problem |
| C2 |
Transfer corona |
| CH |
Lit - Door open |
| CH |
Flashing - DV unit not installed |
| CL |
Drum cleaner connector |
| H2 |
Thermistor |
| H3 |
High fuser temperature |
| H4 |
Low fuser temperature |
| L1 |
Mirror |
| L2 |
Scan |
| L3 |
Scan return |
| L4 |
Drive |
| L5 |
Lens |
| PC |
Key counter |
| U1 |
Dead battery |
| U2 |
Dead battery |
| U3 |
Lens or mirror |
| U4 |
Duplex |
Sharp Z50, 55, 70
| Код ошибки |
Описание |
| (Z70)E |
Magnification dial not set properly |
| H |
Heater problem (fuser has resettable |
| L |
Scan problem |
| P |
Paper feed problem |
Sharp
Z60
| Код ошибки |
Описание |
| F |
Thermal fuse - exposure or fuser |
| H |
Heater problem |
| L |
Scan problem |
| U |
Low Battery |
Sharp
Z800
| Код ошибки |
Описание |
| A1 |
Jam in document feeder |
| A2 |
Jam in document feeder |
| C1 |
Cassette misfeed |
| C2 |
Cassette feed, bypass unplugged |
| C3 |
Bypass misfeed |
| E1 |
Paper feed jam |
| E3 |
Exit jam |
| EE-EL |
Developer overtoned during setup |
| EE-EU |
Developer undertoned during setup |
| J0 |
Developer setup taking place |
| J1 |
Add toner |
| J3 |
Drum unit not installed properly or missing |
| J7 |
Drum unit due for replacing |
| J8 |
Wrong drum unit or power was turned on after J7 displayed |
| L6 |
Key counter or other optional counter accessory problem |
| U1 |
Drive problem |
| U2 |
Scan |
| U3 |
Lens |
| U4-01 |
Fuser thermistor |
| U4-02 |
High fuser temperature |
| U4-03 |
Low fuser temperature |
| U5 |
500 sheet cassette lift motor |
| U6 |
Main board problem |
| U7 |
Document glass too hot (with document feeder) |
| U8 |
Problem with line voltage |
| U9 |
Auto developer setup problem |
Sharp Z810
| Код ошибки |
Описание |
| A1 |
Document feeder problem. |
| CH |
Toner cartridge not installed or not installed properly. |
| H2 |
Sub code 0: Fuser thermistor. |
| H3 |
Sub code 0: Fuser temperature too high. |
| H4 |
Sub code 0: Fuser temperature too low. |
| L1 |
Document feeder problem. |
| L3 |
Scan return problem. Sub code is 0, but there is no more detail.
Could be no scan drive; scan did not leave home; scan did not return
home; scan overloaded; mirror motor problem; scan cable came
off. |
| L4 |
Sub code 1: Main drive problem. Sensor gear motor. |
| L5 |
Sub code 2: Lens drive, motor, sensor |
| P |
Paper feed. |
| U2 |
Sub code 1: Main board EEPROM problem. 4: Memory problem. |
| U5 |
Sub code 5: high temperature at exposing glass when using
document feeder. |
Вы находитесь: Главная
|
| |
|
Ремонт
лазерного принтера |
Ремонт струйного принтера |
|
|
Решение
проблем с включением принтера HP LaserJet 1010 за 1010 рублей |
 |
Ремонт
блока питания принтера HP DeskJet 1220c за 1220 рублей | |
| |
| Восстановление
качества печати |
Установка СНПЧ |
|
 |
Восстановление
качества печати, в струйных принтерах EPSON, HP, CANON за 749 рублей
| 
| Установка
СНПЧ за 999 рублей | |
| |
|
|
Ремонт принтеров
