Коды ошибок
копировальных аппаратов Xerox
Если Ваш копировальный аппарат Xerox выдал на индикации некий
код, то узнать причину возникновения ошибки Вы можете в этом разделе.
Но код ошибки - это лишь следствие сбоя в работе аппарата
Xerox 1012, 1012(RE)
| Код ошибки |
Описание |
| E1 |
Jam between paper feed and fuser |
| E3 |
Jam in fuser |
| E5 |
Clam shell open |
| E6 |
Paper feed section cover is open |
| J1 |
Toner cartridge near empty |
| J3 |
Drum cartridge not seated properly |
| J7 |
Waste toner full (replace drum cartridge) |
| L6 |
Key counter out |
| L8 |
Exposure area overheat |
| U1 |
No clock pulse (drive problem) |
| U2 |
Scan problem |
| U3 |
Lens/mirror problem (RE model only) |
| U4 |
Heat problem |
| U8 |
Exposure lamp control circuit problem |
| E1 |
Jam between paper feed and fuser |
| E3 |
Jam in fuser |
| E5 |
Clam shell open |
| E6 |
Paper feed section cover is open |
| J1 |
Toner cartridge near empty |
| J3 |
Drum cartridge not seated properly |
| J7 |
Waste toner full (replace drum cartridge) |
| L6 |
Key counter out |
| L8 |
Exposure area overheat |
| U1 |
No clock pulse (drive problem) |
| U2 |
Scan problem |
| U3 |
Lens/mirror problem (RE model only) |
| U4 |
Heat problem |
| U8 |
Exposure lamp control circuit
problem |
Xerox 1020
| Код ошибки |
Описание |
| LL |
Probable bad heater lamp |
Xerox 1025
| Код ошибки |
Описание |
| A1 |
DF jam |
| C1 |
PF jam cass. 1 |
| C2 |
PF jam cass. 2 |
| C3 |
PF jam cass. 3 |
| C9 |
Bypass jam |
| E1-1 |
Paper jam before exit switch |
| E1-2 |
Paper jam |
| E1-5 |
Paper jam |
| E1-6 |
Paper jam |
| E3-3 |
Paper jam at exit switch |
| E3-4 |
Paper jam at exit switch |
| E5 |
Front door open |
| F1 |
Collator jam |
| F5 |
Collator interlock |
| F8 |
No power to collator |
| F9 |
Collator bin home switch |
| J7 |
250 copies since toner waste was full |
| L5 |
Original cass. not present after clearing interrupt |
| L6 |
Key counter |
| L8 |
Platen glass too hot |
| U1 |
Main motor clock pulse |
| U2 |
Scan problem |
| U3-1 |
Lens problem |
| U4-1 |
Open thermistor |
| U4-2 |
Low temperature |
| U4-4 |
Temperature |
| U4-5 |
Main PWB |
| U6-1 |
Main PWB |
| U6-2 |
Main PWB |
| U6-3 |
Main board battery |
| U6-4 |
Initialization |
| U8 |
Exposure lamp |
Xerox
1035
| Код ошибки |
Описание |
| A9 |
Scanner location |
| C1 |
Paper feed - upper cassette |
| C2 |
Paper feed - lower cassette |
| C9 |
Bypass jam |
| E5 |
Clam shell is open |
| L6 |
Key counter |
| U1 |
Off/On |
| U2 |
Optics |
| U4 |
Low fuser temperature |
Xerox
1038
| Код ошибки |
Описание |
| A1 |
DF jam |
| C1 |
PF jam cass. 1 |
| C2 |
PF jam cass. 2 |
| C3 |
PF jam cass. 3 |
| C9 |
Bypass jam |
| E1-1 |
Paper jam before exit switch |
| E1-2 |
Paper jam |
| E1-5 |
Paper jam |
| E1-6 |
Paper jam |
| E3-3 |
Paper jam at exit switch |
| E3-4 |
Paper jam at exit switch |
| E5 |
Front door open |
| F1 |
Collator jam |
| F5 |
Collator interlock |
| F8 |
No power to collator |
| F9 |
Collator bin home switch |
| J7 |
250 copies since toner waste was full |
| L5 |
Original cass. not present after clearing interrupt |
| L6 |
Key counter |
| L8 |
Platen glass too hot |
| U1 |
Main motor clock pulse |
| U2 |
Scan problem |
| U3-1 |
Lens problem |
| U4-1 |
Open thermistor |
| U4-2 |
Low temperature |
| U4-4 |
Temperature |
| U4-5 |
Main PWB |
| U6-1 |
Main PWB |
| U6-2 |
Main PWB |
| U6-3 |
Main board battery |
| U6-4 |
Initialization |
| U8 |
Exposure lamp |
Xerox
2830
| Код ошибки |
Описание |
| A9 |
Scanner location |
| C1 |
Paper feed - upper cassette |
| C2 |
Paper feed - lower cassette |
| C9 |
Bypass jam |
| E5 |
Clam shell is open |
| E5 |
Clam shell open |
| L6 |
Key counter |
| U1 |
Off/On |
| U2 |
Optics |
| U4 |
Low fuser temperature |
Xerox
5011, 5012, 5014
| Код ошибки |
Описание |
| C8 |
Bypass jam/no paper |
| C9 |
Bypass jam |
| E1 |
Jam |
| E3 |
Fuser jam |
| E5 |
Clamshell open |
| E6 |
PF section cover open |
| J1 |
Toner cartridge amost empty |
| J3 |
Copy cart (drum unit) missing/not seated right |
| J7 |
Copy cartridge has run 18,000 copies |
| J8 |
Copy cartridge. Improperly seated or possible only one of two
fuses in the cartridge blew |
| L6 |
Key counter |
| L8 |
Exposure glass too hot |
| U1 |
Drive problem |
| U2 |
Scan problem |
| U3 |
Lens or mirror drive problem |
| U4 |
Fuser problem. Heat lamp, thermoswitch, SSR, thermistor |
| U6 |
Battery on main board |
| U8 |
Exposure lamp or exposure lamp
circuit |
Xerox 5016, 5017, 5316,
5317
| Code |
Description |
| A1-1 |
Document feeder feed jam |
| A1-2 |
Document feeder belt jam |
| A2-1 |
Document feeder exit jam |
| A2-2 |
Duplex jam |
| A3 |
DAD interlock |
| A5 |
Duplex and DAD right side interlock |
| A6 |
Copier jams after |
| A9 |
Document feed belt drive motor |
| C1-3 |
Top cassette misfeed |
| C2-3 |
Middle cassette misfeed |
| C3-3 |
Bottom cassette misfeed |
| C9-3 |
Bypass misfeed |
| E1-11 to E1-14 |
Paper jam in machine. Did not reach exit switch soon
enough |
| E1-6 |
Paper path jam |
| E3-31 to E3-34 |
Exit switch jam |
| E3-6 |
Fuser jam |
| E5 |
Front door interlock |
| E6 |
Right side interlock or TTM interlock |
| F1 |
Sorter jam |
| F5 |
Sorter interlock |
| F8 |
Sorter board to copier main board communication problem |
| F9 |
Sorter bins |
Xerox 5018,
5028
| Code |
Description |
| A1 |
Document is ADF |
| A1-8 |
Main board received reset signal |
| A2 |
ADF jams |
| A6, A7 |
ADF jams |
| A9 |
ADF jams |
| C1 - C4 |
Feed jam |
| C5-1 to C5-4 |
Jams in various areas |
| C5-2 |
Jams in various areas |
| C5-3 |
Jams in various areas |
| C5-4 |
Duplex jam |
| E0 |
Machine has reset |
| E1 |
Jam |
| E1-E0 |
Registration jam |
| E1-E5 |
Clamshell interlock |
| E1-E6 |
Right side interlock |
| E1-E7 |
Two tray interlock |
| E1-E8 |
Sorter interlock |
| E1-E9 |
Copy cartridge interlock |
| E2 |
Reset signal happened |
| E3 |
Jam |
| E4 |
Exit jam |
| E4-10 |
Exit jam |
| E4-5 |
Clamshell interlock |
| E4-6 |
Right side interlock |
| E4-7 |
Two tray interlock. Duplex interlock |
| E4-8 |
Sorter interlock |
| E4-9 |
Copy cartridge interlock |
| E5 |
Clamshell interlock |
| E6 |
Right side interlock |
| E7 |
Duplex interlock |
| E9 |
Copy cartridge interlock |
| F3-1 |
Sorter bin home switch |
| F3-2 |
Sorter cam switch |
| F3-3 |
Sorter cam switch |
| J1-1 |
Add toner |
| J1-2 |
Temporary low toner signal |
| J2-0 |
Replace copy cartridge |
| L2 |
2000 copies left on copy cartridge |
| L3 |
ADF to machine communication problem |
| L4 (flashing) |
1000 copies left on fuser web |
| rr |
Bad EPROM on main board |
| U0 |
Main board |
| U2 |
Scan problem |
| U2-1 |
Scan home |
| U3-00 |
Cam drive problem |
| U3-01 |
Cam movement slow |
| U3-04 |
Main board to duplex communication |
| U3-09 |
Cam problem |
| U3-12 |
Jogger problem |
| U3-19 |
Cam problem |
| U3-21 |
Cam problem |
| U3-23 |
Cam problem |
| U3-29 |
Cam problem |
| U3-32 |
Cam problem |
| U3-34 |
Cam problem |
| U3-39 |
Cam problem |
| U3-43 |
Cam problem |
| U3-45 |
Cam problem |
| U3-49 |
Cam problem |
| U3-54 |
Cam problem |
| U3-56 |
Cam problem |
| U3-59 |
Cam problem |
| U4-1 |
Fuser problem. Long warm up |
| U4-2 |
Low fuser temperature after warm up |
| U4-3 |
High fuser temperature |
| U4-4 |
Open fuser thermistor |
| U4-6 |
Replace fuser web |
| U4-7 |
Thermistor signal problem |
| U7-1 |
Copy cartridge belt drive problem |
| U9-3 |
Exposure lamp problem |
| U9-4 |
Toner motor |
| U9-5 |
Problem in warm up |
Xerox
5312, 5313, 5314
| Код ошибки |
Описание |
| C1 |
Upper paper feed problem. Did not reach feed sensor |
| C2 |
Lower paper feed problem. Did not reach feed sensor |
| E1 |
Exit jam. Paper did not reach exit sensor |
| E3 |
Exit jam. Paper still on exit sensor |
| J1 |
Add toner |
| J3 |
Copy cartridge (drum unit) not installed |
| J7 |
Copy cartridge (drum unit) must be replaced |
| J8 |
Copy cartridge (drum unit) problem |
| L6 |
Problem with an accessory. Installed but not initialized |
| U1 |
Drive problem. Main motor, gear etc. |
| U2 |
Scan problem |
| U3 |
Main board dip switches wrong. Lens drive problem |
| U4 |
Fuser problem. Heat lamp, thermal switch, overheat,
thermistor. |
| U6 |
EPROM error |
| U8 |
Auto exposure sensor. No exposure lamp or weak
lamp |
Xerox 5318, 5320,
5322
| Code |
Description |
| A1-11 |
Original ready switch |
| A1-12 |
Feed sensor |
| A1-1 to A1-32 |
All indicate a paper path problem, etc. in the ADF |
| A1-21 |
Original ready switch and document registration sensor or both
the document feed sensor and document registration sensor |
| A1-22 |
ADF registration sensor |
| A1-23 |
Original did not reach ADF registration sensor quickly
enough |
| A1-24 |
ADF sensor stuck down too long |
| A1-25 |
ADF sensor actuated at the wrong time during single sheet
feed |
| A1-26 |
ADF sensor not actuated quickly enough in sheet feed mode |
| A1-31 |
In reverse, ADF sensor is not actuated soon enough |
| A1-32 |
In reverse, ADF sensor is actuated too long |
| A2 |
ADF exit problems |
| A2-1 |
Original ready sensor and ADF exit switch are actuated or ADF
feed in sensor and ADF exit switch are both actuated |
| A2-2 |
ADF exit switch |
| A2-3 |
ADF exit switch is not actuated on time |
| A3 |
Irregular size documents |
| A3-1 |
Wrong size original sensed in 1:1 mode |
| A3-2 |
Wrong size original sensed in the 2:1 mode |
| A5 |
ADF interlock |
| A5 |
ADF interlock |
| A6 |
ADF single sheet document reset. |
| A6-1 |
Reset original |
| A6-2 |
Reset sheet feeder |
| A7 |
Document cover interlock |
| A8 |
ADF exit interlock |
| C1 |
Tray 1 jam |
| C1-2 |
Paper feed problem in tray 1 |
| C1-3 |
Paper does not reach registration |
| C2 |
Tray 2 jam |
| C3 |
Tray 3 jam |
| C3-1 |
Paper feed problem from tray 3 |
| C3-2 |
Paper feed problem from tray 3 |
| C3-3 |
Paper feed problem from tray 1 |
| C6-1 |
Duplex paper feed problem |
| C6-2 |
Duplex and/or tray 1 paper feed problem |
| C6-3 |
Paper feed problem from tray 1 |
| C7-1 |
Paper feed problem from HCF |
| C7-2 |
Paper feed problem from HCF on tray 1 |
| C7-3 |
Paper feed problem from tray 1 |
| C8 |
Paper stays in tray or duplex or HCF |
| C8-1 |
Paper on tray 1 feed sensor |
| C8-2 |
Paper on tray 2 feed sensor |
| C8-3 |
Paper on tray 3 feed sensor |
| C8-4 |
Paper on HCF feed sensor |
| C8-5 |
Paper in duplex section |
| C9 |
Bypass feed problem |
| C9-3 |
Paper from bypass did not reach registration sensor quickly
enough |
| E1-10 to E1-25 |
Internal jam |
| E1-6 |
Paper on registration sensor |
| E2 |
Reset signal happened. Might read E-2 something else. |
| E3-30 to E4-14 |
Exit jam |
| E3-30 to E3-35 |
Exit switch actuated too long |
| E3-6 |
Exit jam |
| E3-6 |
Paper on exit switch |
| E4-10 to E4-14 |
Inverter sensor not actuated. |
| E4-10 to E4-45 |
Paper did not reach inverter switch soon enough |
| E4-15 |
Inverter sensor |
| E4-40 to E4-45 |
Duplex entry sensor |
| E4-6 |
Paper on inverter switch |
| E4-6 |
Inverter sensor |
| E5 |
Front door interlock |
| E6-1 |
Tray 1 interlock |
| E6-2 |
2 tray or duplex interlock |
| E6-3 |
HCF interlock |
| E7-2 |
Duplex inverter interlock |
| E7-3 |
Duplex interlock |
| E8-10 to E8-15 |
Paper on duplex feed sensor is not actuated soon enough |
| E8-6 |
Paper in duplex |
| E8-6 to E8-15 |
Duplex entry sensor |
| F1-1 |
Paper did not reach sorter |
| F1-2 |
Paper stayed on sorter feed sensor |
| F1-6 |
Sorter exit sensor |
| F3 |
Paper size not available for sort/stack |
| F5 |
Sorter interlock |
| H2-1 |
Communication problem between main board and duplex board |
| H2-2 |
Side guard sensor problem |
| H3-1 |
Communication problem between main board and HCF |
| H3-2 |
Upper limit sensor problem on HCF |
| H6-1 |
ADF size sensor |
| H6-2 |
ADF nudgeer sensor |
| H6-3 |
Belt drive motor does not have 24 volts. Black toner is empty,
but 100 copies have been run without changing toner |
| J1 |
Black toner is empty, but 100 copies have been run without
changing toner |
| J3 |
Replace copy cartridge |
| J3 |
No copy cartridge (drum unit) |
| J7 |
Copy cartrige must be replaced |
| J8-1 |
Wrong copy cartridge installed |
| J8-2 |
Copy cartridge EEPROM must be changed |
| L6 |
Auditron or other counter problem |
| L6 |
Key counter not installed |
| L8 |
Platen glass temperature is too high |
| L9 |
Communication problem between interimage erase/edge lamps and
main board |
| U1-1 |
Main motor drive problem |
| U2-1 |
Scan home problem |
| U2-1 to U2-4 |
Scan home sensor |
| U2-2 |
Scan home problem or optics problem |
| U2-3, U2-4 |
Scan home problem |
| U3-1 |
Lens sensor problem |
| U4-1 |
Fuser thermistor open |
| U4-2 |
Fuser did not warm up properly |
| U4-3 |
Fuser temperature too high |
| U4-4 |
Fuser problem. Staying on too long |
| U4-6 |
High fuser temperature |
| U5-1 |
Sorter bin home switch not activated |
| U5-2 |
Sorter bin home switch stayed actuated |
| U5-3 |
Sorter bin home switch |
| U5-4 |
Sorter bin home switch |
| U6-1 |
ROM problem |
| U6-2 |
RAM problem |
| U6-3 |
Low battery |
| U6-4 |
Incorrect value in NVM. Reinitialize main board with code
20-96 |
| U8-1 |
Exposure lamp problem |
| U8-2 |
Communication problem main board and exposure board |
| U8-3 |
Exposure lamp or exposure lamp board problem |
| U8-4 to U8-6 |
Problem with exposure lamp, lamp sensor, lamp
board |
Xerox 5328
| Code |
Description |
| A1 |
Document in ADF |
| A1-8 |
Main board received reset signal |
| A2 |
ADF jams |
| A6 |
ADF registration jam |
| A7 |
ADF interlock |
| A9 |
Tray 1 jam |
| C1 |
Tray 2 jam |
| C2 |
Tray 3 jam |
| C3 |
Bypass feed jams |
| C4 |
Machine has reset |
| E1 |
Jam |
| E1-5 |
Clamshell interlock |
| E1-6 |
Right side interlock |
| E1-7 |
Two tray interlock, or duplex interlock |
| E1-8 |
Sorter interlock |
| E1-9 |
Copy cartridge interlock |
| E1 or E1-0 |
Registration jam |
| E2 |
Reset signal happened |
| E3 |
Jam in transfer area |
| E4 |
Exit jam |
| E4-0 |
Exit jam |
| E4-5 |
Clamshell interlock |
| E4-6 |
Right side interlock |
| E4-7 |
Two tray interlock |
| E4-8 |
Sorter interlock |
| E4-9 |
Copy cartridge interlock |
| E5 |
Clamshell interlock |
| E6 |
Right side interlock |
| E9 |
Copy cartridge interlock |
| F3-1 |
Sorter bin home switch |
| F3-2 |
Sorter cam switch |
| F3-3 |
Sorter cam switch |
| F5 |
Sorter interlock |
| J1-1 |
Add toner |
| J1-2 |
Temporary low toner signal |
| J2-1, J2-2 |
Replace copy cartridge |
| J5, J6 |
ADF to machine communications problem |
| L2 |
2000 copies left on cartridge |
| L3 |
ADF to machine communications problem |
| L4 |
(flashing) 1000 copier left on fuser web |
| L6 |
Auditron or other counter problem |
| LL |
Main board. Try simulation 1.1 to initialize |
| rc |
Wrong operation panel installed |
| rr |
Bad EPROM on main board. Try 1.1 |
| U0 |
Main board |
| U2 |
Scan problem |
| U2-1 |
Scan home |
| U2-2 |
Scan home or scan encoder |
| U2-4 |
Scan home or scan dual page sensor |
| U2-7 |
Scan home |
| U4-1 |
Fuser problem. Long warm up |
| U4-2 |
Low fuser temperature after warm up |
| U4-3 |
High fuser temperature |
| U4-4 |
Open fuser thermistor |
| U4-6 |
Replace fuser web. |
| U4-7 |
Thermistor signal problem |
| U7-1 |
Copy cartridge belt drive problem |
| U9-3 |
Exposure lamp problem |
| U9-4 |
Toner motor |
| U9-5 |
Problem in warm-up |
Xerox
5330
| Code |
Description |
| A1-1 to A1-32 |
All indicate a paper path problem, etc. in the ADF. |
| A2 |
ADF exit problems |
| A3 |
Irregular size documents |
| A5 |
ADF interlock |
| A6 |
ADF single sheet document reset. |
| A7 |
Platen interlock |
| A8 |
ADF exit interlock |
| C1 |
Tray 1 jam |
| C2 |
Tray 2 jam |
| C3 |
Tray 3 jam |
| C6-1, C6-2 |
Jams related to duplex |
| C6-3 |
Registration sensor, re tray 1 |
| C7-1, C7-2 |
HCF feed problems |
| C7-3 |
Tray 1 feed problem |
| C8 |
Paper stays in tray or duplex or HCF |
| C9 |
Bypass feed problem |
| E1-10 to E1-25 |
Internal jam |
| E1-6 |
Paper on registration sensor |
| E2 |
Reset signal happened. Might read E-2 something else. |
| E3-30 to E4-14 |
Exit jam |
| E3-6 |
Exit jam |
| E4-10 to E4-14 |
Inverter sensor not actuated. |
| E4-15 |
Inverter sensor |
| E4-40 to E4-45 |
Duplex entry sensor |
| E4-6 |
Inverter sensor |
| E5 |
Front door interlock |
| E6-1 |
Tray 1 interlock |
| E6-2 |
2 tray or duplex interlock |
| E6-3 |
HCF interlock |
| E7-2, E7-3 |
Duplex interlock |
| E8-6 to E8-15 |
Duplex entry sensor |
| F1-1 |
Sorter entry sensor |
| F1-6 |
Sorter exit sensor |
| F3 |
Paper size not available for sort/stack |
| F5 |
Sorter interlock |
| J1 |
Add toner |
| J3 |
Replace copy cartridge |
| J7 |
Replace copy cartridge |
| J8-1 |
Wrong copy cartridge installed |
| J8-2 |
Copy cartridge EEPROM |
| L6 |
Auditron or other counter problem |
| L8 |
Platen glass temperature is too high |
| L9 |
Communication problem between interimage erase/edge lamps and
main board |
| U1-1 |
Main motor drive problem |
| U2-1 to U2-4 |
Scan home sensor |
| U3-1 |
Lens sensor |
| U4-1 |
Open fuser thermistor |
| U4-2 |
Fuser did not warm up properly |
| U4-3 |
Fuser temperature too high |
| U4-4 |
Fuser problem. Staying on too long |
| U4-6 |
High fuser temperature |
| U5-1 |
Sorter bin home switch not activated |
| U5-2 |
Sorter bin home switch stayed actuated |
| U5-3 |
Sorter bin home switch |
| U5-4 |
Sorter bin home switch |
| U6-1 |
ROM problem |
| U6-2 |
RAM problem |
| U6-3 |
Low battery |
| U6-4 |
Incorrect value in NVM. Reinitialize main board with code
20-96 |
| U8-1 to U8-6 |
Problem with exposure lamp, lamp sensor, lamp
board |
Xerox 5340, 5343
| Code |
Description |
| 00-009; 030 to 033 |
A door was opened while paper was being fed |
| 00-047 |
Paper in duplex |
| 00-1 |
Auditron |
| 00-2 |
Diagnostic error |
| 00-3 |
Faults error |
| 00-4 |
Ric error |
| 00-5 |
Job manager system error |
| 00-6 |
LLM interface |
| 00-7 |
Standby error |
| 00-8 |
Communications error |
| 00-9 |
Xerographic error |
| 01-300 |
Front interlock |
| 01-310 |
Right upper interlock |
| 01-315 |
Left upper interlock |
| 01-320 |
Left lower interlock |
| 01-325 |
Fuser interlock |
| 02-910 |
Key counter missing |
| 02-920 |
Wrong combination of accessories |
| 03-321, 322, 326, 327 |
LLM to ISIL communications problems |
| 03-328 |
IOT communications problem with duplex or tray 4 |
| 03-330 |
IOT communications problems with HCF |
| 03-335, 03-336 |
LLM communications problems with edit |
| 03-340 |
NVM memory |
| 03-341, 03-347 |
Communications problems between IOT and sorter |
| 03-350, 03-354 |
Communications problem with LLM and user interface |
| 03-363, 03-364 |
Communications problem between LLM & optics |
| 03-370, 03-373 |
Communications problem between LLM & DADF |
| 03-380, 384 |
|
| 03-416, 03-422 |
RAM memory problem |
| 03-424, 426 |
NVM memory problem |
| 03-430, 432 |
Billing problem |
| 03-439 |
GRAIB communications problem |
| 03-440 |
RIC communications problem |
| 03-441 |
RIC NVM problem |
| 03-442 |
Modem |
| 03-443, 03-458 |
RIC problems |
| 03-460 |
Serial communications processor problem |
| 04-300 |
Main motor or drive problem |
| 05-100, 05-108 |
DADF registration sensor |
| 05-110 |
DADF exit sensor |
| 05-115, 120 |
DADF jams |
| 05-305 |
DADF document drive |
| 05-310, 312 |
DADF document sensor |
| 05-316 |
DADF registration sensor jam |
| 05-325 |
DADF exit sensor |
| 05-335, 341, 345 |
DADF interlock switches |
| 06-300, 06-310 |
Scan problems |
| 06-315 |
Scan drive |
| 06-320A, 320B, 320C, 325 |
Scan problem |
| 06-330 |
Lens drive |
| 06-340 |
Exposure control problem |
| 06-342 |
LLM CPU problem |
| 06-344, 06-350 |
Exposure cvontrol problem |
| 06-352 |
IOT CPU problem |
| 07-300, 315, 330, 345 |
Tray faults |
| 07-360, 07-370 |
HCF problems |
| 07-375, 380A, 380B |
Duplex problems |
| 08-100, 08-110 |
Feed problems. Lead edge of copy paper is late getting to feed
sensor of tray 1 |
| 08-115, 08-162 |
Feed problem. Lead edge of copy paper is late getting to
registration sensor |
| 08-165 |
Paper jam at registration sensor |
| 08-310, 08-370 |
Paper at a sensor when power is turned on |
| 08-330 |
DADF nudger sensor |
| 08-380 |
Registration side to side problem with home position |
| 08-390 |
Nip |
| 09-300 |
Copy cartridge finished (drum unit) |
| 09-310 |
Add black toner Add color toner |
| 09-320 |
Add color toner |
| 09-330 |
Wrong copy cartridge (wrong drum unit) |
| 09-340 |
Drum cartridge not installed properly |
| 09-350 |
Waste toner full |
| 100 |
A fault has occurred |
| 10-100 |
Exit jam |
| 10-105 |
Exit jam |
| 10-110 |
Vertical sensor jam |
| 10-120, 122, 125 |
Duplex jam |
| 10-150, 155 |
Too much or not enough paper in duplex tray |
| 10-300 |
Fuser thermistor |
| 10-302 |
Low fuser temperature |
| 10-304 |
Bad fuser temp |
| 10-308 |
High fuser temperature or open thermistor |
| 10-310 |
High fuser temperature |
| 10-312 |
Fuser not up to temperature after energy save |
| 10-314 |
Fuser problem |
| 10-320 |
Fuser web finished |
| 10-330, 335, 340 |
Exit switch, vertical sensor switch actuated when power is
turned on |
| 11-100, 11-116 |
Sorter jam |
| 11-150, 11-176 |
Sorter auto stapler jam |
| 11-310, 314, 316 |
Sorter interlock |
| 11-325A, B, C, D, E, F, G |
Sorter index |
| 11-352, 354, 356 |
Sorter auto stapler interlocks |
| 11-365A, B, C, D, E |
Sorter auto stapler bin |
| 11-370, 371, 372A, 373A, 373B, 374 |
Sorter auto stapler staple failure, staple home problem or
tamper home problem |
| 11-385A, 385B, 390A,B,C,D,E, 396A |
Sorter auto stapler staple failure, staple home problem or
tamper home problem |
| 301 |
Fuser web must be replaced |
| 302 |
Copy cartridge (drum unit) must be replaced |
| 501 |
Tray 1 must be rebuilt |
| 502 |
Tray 2 must be rebuilt |
| 503 |
Tray 3 must be rebuilt |
| 504 |
Tray 4 must be rebuilt |
| 505 |
HCF must be rebuilt |
| 506 |
Bypass must be rebuilt |
| 507 |
Duplex unit must be rebuilt |
| 508 |
Replace black developer |
| 509 |
Replace red developer |
| 510 |
Replace green developer |
| 512 |
Replace brown developer |
| 513 |
Copy cartridge (drum unit) will need replacing soon |
| 514 |
Fuser web will need replacing soon |
| 515 |
DADF belt should be replaced |
| 516 |
DADF feed rollers should be replaced |
| 517 |
Replace exposure lamp |
| 518 |
Replace suction filter |
| 519 |
Replace ozone filter |
| 520 |
Replace optics filter |
| 521 |
Replace particle filter |
| 522 |
Replace upper fuser roller |
| 523 |
Replace fuser pawls |
| 524 |
Replace pressure roller |
| 525 |
Replace pressure roller pawls |
| 900-905 |
Key operator calls |
Xerox
5345
| Код ошибки |
Описание |
| 01-01 |
Frequency monitoring and zero cross problem |
| 01-02 |
Interlock |
| 01-03 |
AC power problem |
| 01-04 |
Finisher interlock |
| 01-05 |
24v problem |
| 03-01 |
Optics to main board communication problem |
| 03-02 |
Software reset problem |
| 03-03 |
Could be punched holes in the lead edge of the original |
| 03-04 |
Software problem |
| 03-06 |
Low battery |
| 03-07 |
NVM not initialized or is missing or defective |
| 03-17 |
Communication problem between main board and finisher
board |
| 03-18 |
Initializes one NVM counter to agree to others |
| 03-19 |
All three NVM counter to agree with others |
| 03-20 |
Main board/interface board problems |
| 03-21 |
Problem with RIC NVM |
| 03-22 |
RIC modem problem |
| 03-23 |
RIC real time clock failure. |
| 03-25 |
RIC NVM problem or not initialized |
| 03-27 |
NVM problem |
| 03-28 |
Watchdog software problem |
| 03-29 |
Microprocessor crystal not at correct frequency |
| 03-30 |
No software response from finisher after 20 seconds have
elapsed |
| 06-01 |
Lens did not reach 1.1 position |
| 06-02 |
1/2 rate scanner problem |
| 06-03 |
Scan home problem |
| 06-04 |
Scan home problem |
| 06-05 |
Scan home problem |
| 06-06 |
Scan encoder |
| 06-07 |
Scan encoder |
| 06-08 |
Scan drive boost |
| 06-09 |
Scan encoder |
| 06-11 |
Scan encoder pulse phases |
| 06-12 |
Insufficient scan damping |
| 07-01 |
Duplex tray not home during duplexing |
| 07-02 |
Tray 2 not home when selected |
| 07-13 |
Tray 2 height sensor problem |
| 07-15 |
Tray 2 empty |
| 07-16 |
Tray 1 door open |
| 07-18 |
Tray 1 stack sensor |
| 07-22 |
Tray 1 empty |
| 07-26 |
Tray 1 bypass switch actuated too long |
| 07-27 |
Tray 1 bypass switch deactuated too early |
| 07-30 |
Paper in duplex |
| 07-31 |
Paper in duplex |
| 07-32 |
Duplex tray empty, when paper should be there |
| 08-10 |
Paper did not reach tray 2 input tray sensor |
| 08-11 |
Paper did not reach duplex input sensor |
| 08-12 |
Paper did not reach tray 1 |
| 08-14 |
Paper did not leave tray 2 input sensor quickly enough |
| 08-18 |
Trail edge did not reach tray 2 input sensor quickly
enough |
| 08-19 |
Trail edge did not reach tray 1 input sensor quickly
enough |
| 08-20 |
Paper in duplex |
| 08-21 |
Paper in tray 2 input |
| 08-22 |
Paper in tray 2 or duplex at wrong time |
| 08-23 |
Paper at tray 1 input at wrong time |
| 08-24 |
Paper in tray 1 at wrong time |
| 08-28 |
Upper and lower nips problem |
| 09-08 |
Low toner condition |
| 09-12 |
Drum signals are out of range |
| 09-13 |
Unstable drum patch readings |
| 09-15 |
Patch is too dark |
| 09-16 |
Patch is too light |
| 09-17 |
Open toner container access cover |
| 09-18 |
Low toner level |
| 09-21 |
Low toner sensor disconnected |
| 09-22 |
Low toner condition, even after machine has been theoretically,
adding toner |
| 10-02 |
Low fuser temperature |
| 10-03 |
High fuser temperature |
| 10-06 |
Paper did not reach out put switch |
| 10-07 |
Paper stayed on output switch |
| 10-10 |
Paper did not reach decurler sensor |
| 10-11 |
Paper did not reach decurler sensor |
| 10-12 |
Paper on decurler sensor |
| 10-13 |
Paper did not reach duplex entry sensor in time |
| 10-14 |
Paper did not reach duplex entry sensor in time |
| 10-15 |
Paper on entry sensor at wrong time |
| 10-17 |
Fuser temperature is too high and fuser relay has
deactuated |
| 12-01 |
Paper at finisher input sensor |
| 12-02 |
Paper did not reach finisher |
| 12-03 |
Paper reached finisher too soon |
| 12-05 |
Paper at stapler |
| 12-06 |
Paper at stapler |
| 12-07 |
Paper did not reach stapler |
| 12-08 |
Paper did not reach stapler |
| 12-10 |
Complied motor not working properly |
| 12-15 |
Eject motor problem and/or eject encoder |
| 12-20 |
Stacker motor problem |
| 12-21 |
Stacker interlock |
| 12-22 |
Stacker bottom sensor |
| 12-23 |
Stacker bottom sensor |
| 12-24 |
Stacker bottom sensor senses full |
| 12-25 |
Stack height sensor |
| 12-26 |
Stack height sensor |
| 12-27 |
Stack height sensor |
| 12-30 |
Offset home sensor |
| 12-31 |
Offset home sensor |
| 12-32 |
OCT switch |
| 12-35 |
Eject nip carriage |
| 12-36 |
Eject cam interlock |
| 12-37 |
Eject nip carriage open timing |
| 12-38 |
Eject cam interlock |
| 12-40 |
Tamper motor |
| 12-41 |
Tamper home problem |
| 12-42 |
Tamper home sensor |
| 12-43 |
Staple load sensor |
| 12-44 |
Tamper home sensor |
| 12-45 |
Tamper home sensor |
| 12-50 |
Low on staples |
| 12-51 |
Stapler home sensor |
| 12-52 |
Stapler home sensor |
| 12-53 |
Eject cam interlock |
| 33-37 |
Too few documents |
| 55-01 |
RDH interlock switch open during use |
| 55-04 |
Paper on bypass sensor |
| 55-05 |
Paper at vacuum timing sensor |
| 55-06 |
Paper on output sensor |
| 55-10 |
No paper reached S31 |
| 55-20 |
Paper did not leave S31 at correct time |
| 55-24 |
Set counter arm problem |
| 55-25 |
Documents in input tray not detected |
| 55-27 |
Lead edge did not reach S35 at correct time |
| 55-2955-30 |
Trail edge did not reach S35 at correct time |
| 55-31 |
S32, ADF registration sensor did not see paper at correct
time |
| 55-32 |
S32 did not see trail edge at correct time |
| 55-33 |
S36 One too many documents |
| 55-36 |
One too many documents |
| 55-39 |
Hole count problem on document feeder belt |
| 55-40 |
Document belt travel problem |
| 55-41 |
Document belt mistracking or skewing |
| 55-45 |
Paper at inverter sensor |
| 55-47 |
Inverter sensor did not see paper lead edge at correct
time |
| 55-49 |
More than 50 sheets in input tray |
| 55-50 |
Right side interlock |
| 55-51 |
Left side interlock |
| 55-55 |
Document on glass |
| 93-93 |
NVM has to be initialized after new software
installed |
Xerox 5350,
5352
| Code |
Description |
| 00-009, 030, 031, 032, 033 |
A door was opened while paper was being fed |
| 00-047 |
Paper in duplex |
| 00-1 |
Auditron |
| 00-2 |
Diagnostic error |
| 00-3 |
Faults error |
| 00-4 |
Ric error |
| 00-5 |
Job manager system error |
| 00-6 |
LLM interface |
| 00-7 |
Standby error |
| 00-8 |
Communications error |
| 00-9 |
Xerographic error |
| 01-300 |
Front interlock |
| 01-310 |
Right upper interlock |
| 01-315 |
Left upper interlock |
| 01-320 |
Left lower interlock |
| 01-325 |
Fuser interlock |
| 02-910 |
Key counter missing |
| 02-920 |
Wrong combination of accessories |
| 03-321, 322, 326, 327 |
LLM to ISIL communications problems |
| 03-328 |
IOT communications problem with duplex or tray 4 |
| 03-330 |
IOT communications problems with HCF |
| 03-335, 336 |
LLM communications problems with edit |
| 03-340 |
NVM memory |
| 03-341-347 |
Communications problems between IOT and sorter |
| 03-350-354 |
Communications problem with LLM and user interface |
| 03-363, 364 |
Communications problem between LLM & optics |
| 03-370-03-373 |
Communications problem between LLM & DADF |
| 03-380, 384 |
|
| 03-416-422 |
RAM memory problem |
| 03-424, 426 |
NVM memory problem |
| 03-430, 432 |
Billing problem |
| 03-439 |
GRAIB communications problem |
| 03-440 |
RIC communications problem |
| 03-441 |
RIC NVM problem |
| 03-442 |
Modem |
| 03-443-458 |
RIC problems |
| 03-460 |
Serial communications processor problem |
| 04-300 |
Main motor or drive problem |
| 05-100-108 |
DADF registration sensor |
| 05-110 |
DADF exit sensor |
| 05-115, 120 |
DADF jams |
| 05-305 |
DADF document drive |
| 05-310, 312 |
DADF document sensor |
| 05-316 |
DADF registration sensor jam |
| 05-325 |
DADF exit sensor |
| 05-335, 341, 345 |
DADF interlock switches |
| 06-300-310 |
Scan problems |
| 06-315 |
Scan drive |
| 06-320A, 320B, 320C, 325 |
Scan problem |
| 06-330 |
Lens drive |
| 06-340 |
Exposure control problem |
| 06-342 |
LLM CPU problem |
| 06-344-350 |
Exposure cvontrol problem |
| 06-352 |
IOT CPU problem |
| 07-300, 315, 330, 345 |
Tray faults |
| 07-360-370 |
HCF problems |
| 07-375, 380A, 380B |
Duplex problems |
| 08-100-110 |
Feed problems. Lead edge of copy paper is late getting to feed
sensor of tray 1 |
| 08-115-162 |
Feed problem. Lead edge of copy paper is late getting to
registration sensor |
| 08-165 |
Paper jam at registration sensor |
| 08-310-370 |
Paper at a sensor when power is turned on |
| 08-330 |
DADF nudger sensor |
| 08-380 |
Registration side to side problem with home position |
| 08-390 |
Nip |
| 09-300 |
Copy cartridge finished (drum unit) |
| 09-310 |
Add black toner Add color toner |
| 09-320 |
Add color toner |
| 09-330 |
Wrong copy cartridge (wrong drum unit) |
| 09-340 |
Drum cartridge not installed properly |
| 09-350 |
Waste toner full |
| 100 |
A fault has occurred |
| 10-100 |
Exit jam |
| 10-105 |
Exit jam |
| 10-110 |
Vertical sensor jam |
| 10-120, 122, 125 |
Duplex jam |
| 10-150, 155 |
Too much or not enough paper in duplex tray |
| 10-300 |
Fuser thermistor |
| 10-302 |
Low fuser temperature |
| 10-304 |
Bad fuser temp |
| 10-308 |
High fuser temperature or open thermistor |
| 10-310 |
High fuser temperature |
| 10-312 |
Fuser not up to temperature after energy save |
| 10-314 |
Fuser problem |
| 10-320 |
Fuser web finished |
| 10-330, 335, 340 |
Exit switch, vertical sensor switch actuated when power is
turned on |
| 11-100-116 |
Sorter jam |
| 11-150-176 |
Sorter auto stapler jam |
| 11-310, 314, 316 |
Sorter interlock |
| 11-325A,B,C,D,E,F,G |
Sorter index |
| 11-352, 354, 356 |
Sorter auto stapler interlocks |
| 11-365A,B,C,D,E |
Sorter auto stapler bin |
| 11-370,371,372A,373A,373B,374 |
Sorter auto stapler staple failure, staple home problem or
tamper home problem |
| 11-385A,385B,390A,B,C,D,E,396A |
Sorter auto stapler staple failure, staple home problem or
tamper home problem |
| 301 |
Fuser web must be replaced |
| 302 |
Copy cartridge (drum unit) must be replaced |
| 501 |
Tray 1 must be rebuilt |
| 502 |
Tray 2 must be rebuilt |
| 503 |
Tray 3 must be rebuilt |
| 504 |
Tray 4 must be rebuilt |
| 505 |
HCF must be rebuilt |
| 506 |
Bypass must be rebuilt |
| 507 |
Duplex unit must be rebuilt |
| 508 |
Replace black developer |
| 509 |
Replace red developer |
| 510 |
Replace green developer |
| 512 |
Replace brown developer |
| 513 |
Copy cartridge (drum unit) will need replacing soon |
| 514 |
Fuser web will need replacing soon |
| 515 |
DADF belt should be replaced |
| 516 |
DADF feed rollers should be replaced |
| 517 |
Replace exposure lamp |
| 518 |
Replace suction filter |
| 519 |
Replace ozone filter |
| 520 |
Replace optics filter |
| 521 |
Replace particle filter |
| 522 |
Replace upper fuser roller |
| 523 |
Replace fuser pawls |
| 524 |
Replace pressure roller |
| 525 |
Replace pressure roller pawls |
| 900-905 |
Key operator calls |
Xerox
5355
| Код ошибки |
Описание |
| 01-01 |
Frequency monitoring and zero cross problem |
| 01-02 |
Interlock |
| 01-03 |
AC power problem |
| 01-04 |
Finisher interlock |
| 01-05 |
24v problem |
| 03-01 |
Optics to main board communication problem |
| 03-02 |
Software reset problem |
| 03-03 |
Could be punched holes in the lead edge of the original |
| 03-04 |
Software problem |
| 03-06 |
Low battery |
| 03-07 |
NVM not initialized or is missing or defective |
| 03-17 |
Communication problem between main board and finisher
board |
| 03-18 |
Initializes one NVM counter to agree to others |
| 03-19 |
All three NVM counter to agree with others |
| 03-20 |
Main board/interface board problems |
| 03-21 |
Problem with RIC NVM |
| 03-22 |
RIC modem problem |
| 03-23 |
RIC real time clock failure. |
| 03-25 |
RIC NVM problem or not initialized |
| 03-27 |
NVM problem |
| 03-28 |
Watchdog software problem |
| 03-29 |
Microprocessor crystal not at correct frequency |
| 03-30 |
No software response from finisher after 20 seconds have
elapsed |
| 06-01 |
Lens did not reach 1.1 position |
| 06-02 |
1/2 rate scanner problem |
| 06-03 |
Scan home problem |
| 06-04 |
Scan home problem |
| 06-05 |
Scan home problem |
| 06-06 |
Scan encoder |
| 06-07 |
Scan encoder |
| 06-08 |
Scan drive boost |
| 06-09 |
Scan encoder |
| 06-11 |
Scan encoder pulse phases |
| 06-12 |
Insufficient scan damping |
| 07-01 |
Duplex tray not home during duplexing |
| 07-02 |
Tray 2 not home when selected |
| 07-13 |
Tray 2 height sensor problem |
| 07-15 |
Tray 2 empty |
| 07-16 |
Tray 1 door open |
| 07-18 |
Tray 1 stack sensor |
| 07-22 |
Tray 1 empty |
| 07-26 |
Tray 1 bypass switch actuated too long |
| 07-27 |
Tray 1 bypass switch deactuated too early |
| 07-30 |
Paper in duplex |
| 07-31 |
Paper in duplex |
| 07-32 |
Duplex tray empty, when paper should be there |
| 08-10 |
Paper did not reach tray 2 input tray sensor |
| 08-11 |
Paper did not reach duplex input sensor |
| 08-12 |
Paper did not reach tray 1 |
| 08-14 |
Paper did not leave tray 2 input sensor quickly enough |
| 08-18 |
Trail edge did not reach tray 2 input sensor quickly
enough |
| 08-19 |
Trail edge did not reach tray 1 input sensor quickly
enough |
| 08-20 |
Paper in duplex |
| 08-21 |
Paper in tray 2 input |
| 08-22 |
Paper in tray 2 or duplex at wrong time |
| 08-23 |
Paper at tray 1 input at wrong time |
| 08-24 |
Paper in tray 1 at wrong time |
| 08-28 |
Upper and lower nips problem |
| 09-08 |
Low toner condition |
| 09-12 |
Drum signals are out of range |
| 09-13 |
Unstable drum patch readings |
| 09-15 |
Patch is too dark |
| 09-16 |
Patch is too light |
| 09-17 |
Open toner container access cover |
| 09-18 |
Low toner level |
| 09-21 |
Low toner sensor disconnected |
| 09-22 |
Low toner condition, even after machine has been theoretically,
adding toner |
| 10-02 |
Low fuser temperature |
| 10-03 |
High fuser temperature |
| 10-06 |
Paper did not reach out put switch |
| 10-07 |
Paper stayed on output switch |
| 10-10 |
Paper did not reach decurler sensor |
| 10-11 |
Paper did not reach decurler sensor |
| 10-12 |
Paper on decurler sensor |
| 10-13 |
Paper did not reach duplex entry sensor in time |
| 10-14 |
Paper did not reach duplex entry sensor in time |
| 10-15 |
Paper on entry sensor at wrong time |
| 10-17 |
Fuser temperature is too high and fuser relay has
deactuated |
| 12-01 |
Paper at finisher input sensor |
| 12-02 |
Paper did not reach finisher |
| 12-03 |
Paper reached finisher too soon |
| 12-05 |
Paper at stapler |
| 12-06 |
Paper at stapler |
| 12-07 |
Paper did not reach stapler |
| 12-08 |
Paper did not reach stapler |
| 12-10 |
Complied motor not working properly |
| 12-15 |
Eject motor problem and/or eject encoder |
| 12-20 |
Stacker motor problem |
| 12-21 |
Stacker interlock |
| 12-22 |
Stacker bottom sensor |
| 12-23 |
Stacker bottom sensor |
| 12-24 |
Stacker bottom sensor senses full |
| 12-25 |
Stack height sensor |
| 12-26 |
Stack height sensor |
| 12-27 |
Stack height sensor |
| 12-30 |
Offset home sensor |
| 12-31 |
Offset home sensor |
| 12-32 |
OCT switch |
| 12-35 |
Eject nip carriage |
| 12-36 |
Eject cam interlock |
| 12-37 |
Eject nip carriage open timing |
| 12-38 |
Eject cam interlock |
| 12-40 |
Tamper motor |
| 12-41 |
Tamper home problem |
| 12-42 |
Tamper home sensor |
| 12-43 |
Staple load sensor |
| 12-44 |
Tamper home sensor |
| 12-45 |
Tamper home sensor |
| 12-50 |
Low on staples |
| 12-51 |
Stapler home sensor |
| 12-52 |
Stapler home sensor |
| 12-53 |
Eject cam interlock |
| 33-37 |
Too few documents |
| 55-01 |
rdh interlock switch open during use |
| 55-04 |
Paper on bypass sensor |
| 55-05 |
Paper at vacuum timing sensor |
| 55-06 |
Paper on output sensor |
| 55-10 |
No paper reached S31 |
| 55-20 |
Paper did not leave S31 at correct time |
| 55-24 |
Set counter arm problem |
| 55-25 |
Documents in input tray not detected |
| 55-27 |
Lead edge did not reach S35 at correct time |
| 55-2955-30 |
Trail edge did not reach S35 at correct time |
| 55-31 |
S32, ADF registration sensor did not see paper at correct
time |
| 55-32 |
S32 did not see trail edge at correct time |
| 55-33 |
S36 One too many documents |
| 55-36 |
One too many documents |
| 55-39 |
Hole count problem on document feeder belt |
| 55-40 |
Document belt travel problem |
| 55-41 |
Document belt mistracking or skewing |
| 55-45 |
Paper at inverter sensor |
| 55-47 |
Inverter sensor did not see paper lead edge at correct
time |
| 55-49 |
More than 50 sheets in input tray |
| 55-50 |
Right side interlock |
| 55-51 |
Left side interlock |
| 55-55 |
Document on glass |
| 93-93 |
NVM has to be initialized after new software
installed |
Xerox XC520, 540,
560, 580
| Код ошибки |
Описание |
| H2 |
Fuser thermistor |
| H3 |
Fuser temperature too high. Must be reset in diagnostics |
| H4 |
Fuser temperature too low. Must be reset in diagnostics |
| L3 |
Scan problem |
| L4 |
Min motor drive problem |
| L8 |
Exposure lamp not lightning or not enough light reaching auto
exposure sensor |
| P |
Paper did not feed |
Xerox
5622
| Code |
Description |
| A1-1 to A1-32 |
All indicate a paper path problem, etc. in the ADF |
| A2 |
ADF exit problems |
| A3 |
Irregular size documents |
| A5 |
ADF interlock |
| A6 |
ADF single sheet document reset |
| A7 |
Platen interlock |
| A8 |
ADF exit interlock |
| C1 |
Tray 1 jam |
| C2 |
Tray 2 jam |
| C3 |
Tray 3 jam |
| C6-1, C6-2 |
Jams related to duplex |
| C6-3 |
Registration sensor, re tray 1 |
| C7-1, C7-2 |
HCF feed problems |
| C7-3 |
Tray 1 feed problem |
| C8 |
Paper stays in tray or duplex or HCF |
| C9 |
Bypass feed problem |
| E1-10 to E1-25 |
Internal jam |
| E1-6 |
Paper on registration sensor |
| E2 |
Reset signal happened. Might read E-2 something else |
| E3-30 to E4-14 |
Exit jam |
| E3-6 |
Exit jam |
| E4-10 to E4-14 |
Inverter sensor not actuated |
| E4-15 |
Inverter sensor |
| E4-40 to E4-45 |
Duplex entry sensor |
| E4-6 |
Inverter sensor |
| E5 |
Front door interlock |
| E6-1 |
Tray 1 interlock |
| E6-2 |
2 tray or duplex interlock |
| E6-3 |
HCF interlock |
| E7-2, E7-3 |
Duplex interlock |
| E8-6 to E8-15 |
Duplex entry sensor |
| F1-1 |
Sorter entry sensor |
| F1-6 |
Sorter exit sensor |
| F3 |
Paper size not available for sort/stack |
| F5 |
Sorter interlock |
| J1 |
Add toner |
| J3 |
Replace copy cartridge |
| J7 |
Replace copy cartridge |
| J8-1 |
Wrong copy cartridge installed |
| J8-2 |
Copy cartridge EEPROM |
| L6 |
Auditron or other counter problem |
| L8 |
Platen glass temperature is too high |
| L9 |
Communication problem between interimage erase/edge lamps and
main board |
| U1-1 |
Main motor drive problem |
| U2-1 to U2-4 |
Scan home sensor |
| U3-1 |
Lens sensor |
| U4-1 |
Open fuser thermistor |
| U4-2 |
Fuser did not warm up properly |
| U4-3 |
Fuser temperature too high |
| U4-4 |
Fuser problem. Staying on too long |
| U4-6 |
High fuser temperature |
| U5-1 |
Sorter bin home switch not activated |
| U5-2 |
Sorter bin home switch stayed actuated |
| U5-3, U5-4 |
Sorter bin home switch |
| U6-1 |
ROM problem |
| U6-2 |
RAM problem |
| U6-3 |
Low battery |
| U6-4 |
Incorrect value in NVM. Reinitialize main board with code
20-96 |
| U8-1 to U8-6 |
Problem with exposure lamp, lamp sensor, lamp
board |
Вы находитесь: Главная
|
Ремонт принтеров
