Коды ошибок аналоговых
копировальных аппаратов Canon
копировальных аппаратов Canon
Если Ваш аналоговый копировальный аппарат Canon выдал на
индикации некий код, то узнать причину возникновения ошибки Вы можете в
этом разделе.
Но код ошибки - это лишь следствие сбоя в работе аппарат.
| Список моделей: |
| 10,24,115,14,NP112,PC3 |
210, 300 |
25, 250, 270,
350 |
| 400, 500 |
5L,5ll,5Lll,3ll,2L,PC1,PC2,PC5 |
NP1215 |
| 150 |
1500 |
155 |
| 20 |
2015 |
2020,
2120 |
| 3025 |
3030, 3050 |
3225 |
| 3325 |
3525, 3725 |
3825 |
| 4035 |
4050, 4080 |
4540 |
| 4835 |
6012F |
6030 |
| 6035 |
6045 |
6085 |
| 6150 |
6212 |
6230 |
| 6650 |
7050 |
720, 740, 770,
790 |
| 7550 |
8070, 8570 |
8530,
8580 |
| 9800 |
A-1 |
C-120 |
| C-160 |
C-180 |
C200D |
| NP |
PC |
PC6 |
| PC7 |
NP7161 |
|
Canon 10, 24, 115, 14, NP112, PC3
| Код ошибки |
Описание |
| E0 |
Heat lamp |
| E2 |
Scanner |
Canon
210, 300
| Код ошибки |
Описание |
| E0 |
Heat problem |
| E1 |
Sorter |
| E2 |
Scanner |
| E4 |
Drum drive |
| E5 |
Lens drive |
| E6 |
Exposure lamp |
| E7 |
Mirror sensors |
Canon 25, 250, 270, 350
| Код ошибки |
Описание |
| E0 |
Thermistor/thermoswitch or heat lamps |
| E1 |
Sorter |
| E2 |
Scanner home |
| E3 |
Scanner return |
| E4 |
Right front door/main motor |
| E5 |
Lens home |
| E6 |
Lamp regulator |
| E8 |
Counter wire |
Canon 400, 500
| Код ошибки |
Описание |
| E0 |
Fuser |
| E1 |
Sorter |
| E2 |
Scan home |
| E3 |
Scan |
| E4 |
Clock pulse or open RF door |
| E5 |
Lens position |
| E6 |
Exposure lamp, fuse 2 |
| E8 |
Counter |
Canon
5L, 5ll, 5Lll, 3ll, 2L, PC-1, PC-2, PC-5
| Код ошибки |
Описание |
| E0 |
Heater problem |
| E1 |
The heater film has gone off center. Turn machine off & on,
make sure it's level etc. |
| E2 |
Scan problme |
| E6 |
Exposure lamp or exposure lamp
sensor |
Canon
NP1215
| Код ошибки |
Описание |
| E000 |
Low temperature, thermoswitch, thermistor or AC driver |
| E001 |
High temperature, thermistor, AC driver |
| E030 |
Counter |
| E202 |
Scan not returning home. Scan not leaving home |
| E221 |
Lamp regulator board |
| E400 |
Document feeder problem |
| E500 |
Sorter problem |
Canon 150
| Код ошибки |
Описание |
| E0 |
Thermistor, thermal switch, heat |
| E1 |
Sorter, scanner home |
| E2 |
Motor, clock pulse |
| E3 |
Scan problem |
| E4 |
Lens home |
| E5 |
Lamp regulator/document sensor |
| E6 |
Motor control |
| E7 |
Total counter |
| E8 |
Lamp regulator |
| E9 |
Copyboard drive motor/board |
| ED |
Motor control PCB |
| EE |
DC controller on motor |
| E001 |
High fuser temperature. Shorter fuser thermistor |
| E030 |
Total counter disconnected or open |
| E202 |
Scan problem |
| E210 |
Lens problem |
| E221 |
DC power supply, lamp regulator board or main board |
| E400 |
Document feeder board problem |
| E500 |
Sorter board problem |
| E000 |
Low fuser temperature |
Canon 1500
| Код ошибки |
Описание |
| E001 |
High fuser temperature. Shorter fuser thermistor |
| E030 |
Total counter disconnected or open |
| E202 |
Scan problem |
| E210 |
Lens problem |
| E221 |
DC power supply, lamp regulator board or main board |
| E400 |
Document feeder board problem |
| E500 |
Sorter board problem |
| E000 |
Low fuser temperature |
Canon 155
| Код ошибки |
Описание |
| E0 |
Thermistor, thermal switch, heat |
| E1 |
Sorter, scanner home |
| E2 |
Motor, clock pulse |
| E3 |
Scan problem |
| E4 |
Lens home |
| E5 |
Lamp regulator/document density sensor |
| E6 |
Motor control board |
| E7 |
Total counter |
| E8 |
Lamp regulator |
| E9 |
Copyboard drive motor/board |
| ED |
Motor control PCB |
| EE |
DC controller on motor |
Canon 20
| Код ошибки |
Описание |
| E2 |
Scanner |
| E0 |
Heat lamp |
| D030 |
Total counter or DC controller |
| E00 |
Heater (Press SW301 twice to reset) |
| E001 |
Over temperature |
| E010 |
Drum drive clock pulse |
| E202 |
Scan home position |
| E204 |
Registration switch (scan problem) |
| E210 |
Lens home |
| E221 |
Lamp regulator or DC controller |
| E400 |
Document feed problem (Check circuit breaker) |
| E500 |
Sorter (Check circuit breaker) |
| E000 |
Fuser problem. Low temperature. Lamp, thermal switch, AC
driver |
| E001 |
Fuser problem. High temperature. Triac, AC driver, pinched
wire |
| E004 |
Fuser problem |
| E053 |
Sorter |
| E030 |
Counter |
| E202 |
Scan |
| E210 |
Lens |
| E221 |
Exposure lamp regulator board, thermal fuse, exposure lamp |
| E400 |
ADF |
| E500 |
Sorter |
| E710 |
DC controller (main board) |
| E001 |
Heater problem |
Canon 2015
| Код ошибки |
Описание |
| D030 |
Total counter or DC controller |
| E00 |
Heater (Press SW301 twice to reset) |
| E001 |
Over temperature |
| E010 |
Drum drive clock pulse |
| E202 |
Scan home position |
| E204 |
Registration switch (scan problem) |
| E210 |
Lens home |
| E221 |
Lamp regulator or DC controller |
| E400 |
Document feed problem (Check circuit breaker) |
| E500 |
Sorter (Check circuit breaker) |
Canon 2020, 2120
| Код ошибки |
Описание |
| E000 |
Fuser problem. Low temperature. Lamp, thermal switch, AC
driver |
| E001 |
Fuser problem. High temperature. Triac, AC driver, pinched
wire |
| E004 |
Fuser problem |
| E0053 |
Sorter |
| E030 |
Counter |
| E202 |
Scan |
| E210 |
Lens |
| E221 |
Exposure lamp regulator board, thermal fuse, exposure lamp |
| E400 |
ADF |
| E500 |
Sorter |
| E710 |
DC controller (main board) |
Canon 3025
| Код ошибки |
Описание |
| E000 |
Fuser problem |
| E010 |
Main motor, motor board, clock pulse |
| E030 |
Counter |
| E050 |
Duplex side to side problem |
| E051 |
Crossway registration |
| E200 |
Scan problem |
| E200 |
Scan reverse sensor or scan |
| E202 |
Scan return problem |
| E204 |
Document sensor, scan reverse sensor or scale |
| E210 |
Lens problem |
| E220 |
Lens |
| E220 |
Blank lamp open or lens home problem |
| E240 |
DC controller |
| E400 |
Document feeder board problem or document feeder interface
problem |
| E500 |
Sorter |
| E620 |
Editing problem |
Canon 3030, 3050
| Код ошибки |
Описание |
| E000 |
Fuser temp low. Heat lamp, thermoswitch, thermistor, SSR |
| E001 |
Fuser temperature too high or shorted thermistor |
| E002 |
Fuser temperature too low |
| E003 |
Fuser temperature too low |
| E004 |
SSR, or lamp reg. board |
| E010 |
Drive problem |
| E022 |
DV unit switching problem |
| E030 |
Counter not working/open |
| E202 |
Scan problem. Scan sensor, scan motor |
| E204 |
Scan problem. Scan sensor, scan motor |
| E210 |
Lens problem. Lens sensor, lens motor |
| E220 |
Exposure lamp |
| E240 |
DC controller (main board) |
| E400 |
RDF circuit board |
| E401 |
RDF pickup motor drive |
| E402 |
RDF belt motor drive |
| E403 |
RDF feed drive problem |
| E404 |
RDF exit motor |
| E411 |
RDF sensor problem |
| E500 |
Sorter board problem |
| E510 |
Sorter feed motor |
| E512 |
Sorter delivery motor |
| E514 |
Sorter delivery motor |
| E520 |
Sort stack motor |
| E530 |
Vibrator motor |
| E531 |
Stapler motor |
| E535 |
Vibrator motor |
| E540 |
Shift problem |
| E541 |
Shift problem |
| E710 |
DC controller |
| E711 |
DC controller |
| E712 |
DC controller. Document feeder board or cable |
| E800 |
Auto shut off relay |
Canon 3225
| Код ошибки |
Описание |
| E000 |
Fuser problem |
| E010 |
Drive |
| E030 |
Counter |
| E050 |
Duplex side to side problem |
| E051 |
Duplex side to side problem |
| E200 |
Scan problem |
| E202 |
Scan return problem |
| E204 |
Scan |
| E210 |
Lens problem |
| E220 |
Blank lamp open or lens home problem |
| E240 |
Bad DC controller |
| E400 |
Document feeder board problem or document feeder interface
problem |
| E500 |
Sorter |
| E620 |
Editing problem |
Canon 3325
| Код ошибки |
Описание |
| E000 |
Low fuser temperature. Heat lamp, thermoswitch, thermofuse,
thermistor, SSR |
| E001 |
High fuser temperature. Thermistor, SSR, pinched wire |
| E002 |
Low fuser temperature. Same as E002 |
| E003 |
Same as E000/E001 |
| E010 |
Same as E002 |
| E022 |
Motor drive problem |
| E030 |
Counter |
| E202 |
Scan motor, sensor |
| E204 |
Scan motor, sensor |
| E210 |
Lens motor, sensor |
| E220 |
Exposure lamp |
| E240 |
DC controller (main board) |
| E401 |
Pickup drive problem (might be Doc. Feeder) |
| E402 |
Document belt drive problem |
| E404 |
Exit motor (document feeder) |
| E411 |
Document sensor (document feeder) |
| E500 |
Sorter/machine communication problem |
| E510 |
Sorter drive problem |
| E530 |
Sorter home sensor |
| E531 |
Stapler unit swing sensor |
| E540 |
Sorter cam sensor |
| E541 |
Sorter cam sensor |
| E710 |
DC controller (main board) |
| E712 |
DC controller or document feeder
board |
Canon
3525, 3725
| Код ошибки |
Описание |
| E000 |
Fuser problem |
| E010 |
Main motor, motor board, clock pulse |
| E030 |
Counter |
| E050 |
Duplex side to side problem |
| E051 |
Crossway registration |
| E200 |
Scan problem |
| E202 |
Scan return problem |
| E202 |
Scan home sensor or home scan |
| E204 |
Document sensor, scan reverse sensor or scale |
| E210 |
Lens |
| E220 |
Blank lamp open or lens home problem |
| E240 |
DC controller |
| E400 |
Document feeder board problem or document feeder interface
problem |
| E500 |
Sorter |
| E620 |
Editing problem |
Canon 3825
| Код ошибки |
Описание |
| E000 |
Low fuser temperature. Heat lamp, thermoswitch, thermofuse,
thermistor, SSR |
| E001 |
High fuser temperature. Thermistor, SSR, pinched wire |
| E002 |
Low fuser temperature. Same as E002 |
| E003 |
Same as E000/E001 |
| E010 |
Same as E002 |
| E022 |
Motor drive problem |
| E030 |
Counter |
| E202 |
Scan motor, sensor |
| E204 |
Scan motor, sensor |
| E210 |
Lens motor, sensor |
| E220 |
Exposure lamp |
| E240 |
DC controller (main board) |
| E401 |
Pickup drive problem (might be Doc. Feeder) |
| E402 |
Document belt drive problem |
| E404 |
Exit motor (document feeder) |
| E411 |
Document sensor (document feeder) |
| E500 |
Sorter/machine communication problem |
| E510 |
Sorter drive problem |
| E530 |
Sorter home sensor |
| E531 |
Stapler unit swing sensor |
| E540 |
Sorter cam sensor |
| E541 |
Sorter cam sensor |
| E710 |
DC controller (main board) |
| E712 |
DC controller or document feeder
board |
Canon
4035
| Код ошибки |
Описание |
| E000 |
Low fuser temperature |
| E001 |
High fuser temperature |
| E010 |
Main motor clock pulse |
| E011 |
Bind or load on main motor |
| E020 |
No TF for 3 minutes |
| E030 |
Copy counter |
| E050 |
Duplex unit |
| E201 |
Scan motor |
| E203 |
Scan motor |
| E210 |
Lens home |
| E240 |
DC controller |
| E241 |
DC controller |
| E320 |
CCD |
| E400 |
DC controller, 24V |
| E500 |
DC controller, 24V |
| E510 |
Finisher feed motor |
| E520 |
Stacker motor |
| E530 |
Guide plate shift motor |
| E531 |
Stapler motor |
| E620 |
DC controller, edit board |
Canon 4050, 4080
| Код ошибки |
Описание |
| E000 |
No fuser heat |
| E001 |
High fuser temperature or shorter thermistor |
| E002 |
Low temperature or bad thermistor |
| E003 |
Fuser problem |
| E004 |
Bad SSR (heat staying on) |
| E010 |
Drive |
| E020 |
Black toner motor |
| E030 |
Counter |
| E080 |
Interface problem with color unit |
| E081 |
Vertical drive motor |
| E082 |
Horizontal drive motor |
| E083 |
Color unit sensor on right |
| E084 |
Color unit sensor on left |
| E085 |
Color unit release sensor or release or solonoid |
| E086 |
Color unit claw release |
| E089 |
Laser problem |
| E100 |
Laser problem |
| E110 |
Laser motor |
| E140 |
Laser |
| E202 |
Scan |
| E203 |
Scan |
| E204 |
Scan |
| E210 |
Lens |
| E223 |
Color unit filter drive motor |
| E240 |
DC controller |
| E401 |
RDF pickup motor |
| E402 |
RDF belt motor |
| E403 |
RDF feed motor |
| E411 |
RDF document sensor |
| E500 |
Sorter-Copier communication error |
| E510 |
Sorter drive |
| E512 |
Sorter drive |
| E513 |
Sorter drive |
| E514 |
Sorter drive |
| E520 |
Top limit sensor or stack sensor |
| E530 |
Sorter home sensor |
| E531 |
Stapler home sensor |
| E535 |
Stapler swing sensor |
| E540 |
Stack shift sensor |
| E660 |
IC card |
| E710 |
DC controller |
| E711 |
DC controller |
| E714 |
DC controller |
| E800 |
Power off circuit |
Canon 4540
| Код ошибки |
Описание |
| E00 |
Low fuser temperature |
| E001 |
High fuser temperature |
| E010 |
Main motor clock pulse |
| E011 |
Bind or load on main motor |
| E020 |
No TF for 3 minutes |
| E030 |
Copy counter |
| E050 |
Duplex unit |
| E201 |
Scan motor |
| E203 |
Scan motor |
| E210 |
Lens home |
| E240 |
DC controller |
| E241 |
DC controller |
| E320 |
CCD |
| E400 |
DC controller, 24V |
| E500 |
DC controller, 24V |
| E510 |
Finisher feed motor |
| E520 |
Stacker motor |
| E530 |
Guide plate shift motor |
| E531 |
Stapler motor |
| E620 |
DC controller, edit board |
Canon 4835
| Код ошибки |
Описание |
| E000 |
Low fuser temperature |
| E001 |
High fuser temperature |
| E002 |
Low fuser temperature |
| E003 |
Low fuser temperature |
| E010 |
Drive |
| E030 |
Counter |
| E080 |
Color change board problems |
| E081 |
Color horizontal motor problem |
| E082 |
Color horizontal motor problem |
| E083 |
Color problem in vertical direction |
| E084 |
Color problem in vertical direction |
| E085 |
Color problem in vertical direction |
| E086 |
Color unit claw release problem |
| E089 |
Color change incomplete |
| E100 |
Laser problem |
| E110 |
Laser motor problem |
| E140 |
Laser unit |
| E203 |
Scan drive problem |
| E210 |
Lens not home or won't leave home |
| E240 |
DC controller |
| E401 |
Document feeder pick up motor |
| E402 |
Document feeder belt motor |
| E403 |
RADF feed motor |
| E404 |
Document feeder motor |
| E411 |
Document feeder sensor |
| E500 |
Sorter to DC control interface problem |
| E510 |
Stapler/sorter motor |
| E530 |
Stapler swing motor |
| E531 |
Stapler swing motor |
| E540 |
Sorter bin motor |
| E541 |
Sorter bin motor |
| E710 |
DC controller |
| E711 |
DC controller |
| E712 |
DC controller to document feeder interface
problem |
Canon
6012F
| Код ошибки |
Описание |
| C |
No problem. Means that the machine is correcting the fuser film
tracking |
| CC |
Drum must be changed. Could be the drum serial number is
identified by the logic as being non-compatible to that particular
copier |
| E000 |
Low fuser temperature |
| E001 |
High fuser temperature |
| E002 |
High fuser temperature |
| E003 |
Erratic fuser temperature |
| E007 |
Fuser film off track and will not repair itself |
| E010 |
Main drive problem |
| E030 |
Counter problem |
| E064 |
Scan problem, or power supply |
| E202 |
Scan problem |
| E210 |
Lens drive problem or lens sensor |
| E220 |
Exposure lamp stays on or off |
| E240 |
DC controller (main board) or composite power supply |
| E261 |
Zero cross problem. Power frequency or composite power
supply |
| E400 |
Communication problem between boards |
| E803 |
24 volt problem |
| EO |
Fuser problem |
| H |
Fuser overheat |
Canon 6030
| Код ошибки |
Описание |
| E000 |
Fuser did not heat up |
| E001 |
Fuser temperature too high |
| E002 |
Fuser temperature not rising at correct pace |
| E003 |
Fuser temperature drops |
| E004 |
SSR shorted |
| E210 |
Lens home problem |
| E212 |
Lens home problem |
| E220 |
Exposure lamp problem |
| E224 |
Blank shutter home problem |
| E240 |
DC controller or composite power supply problem |
| E400 |
Data communication problem |
| E401 |
Pickup motor problem |
| E402 |
Belt motor problem |
| E403 |
Feeder motor |
| E404 |
Delivery motor |
| E411 |
Document detect sensor |
| E500 |
Communication problem with copier |
| E510 |
Feeder motor |
| E530 |
Home sensor |
| E531 |
Staple swing sensor problem |
| E540 |
Bin shift motor rotation problem |
| E541 |
Bin motor |
| E710 |
DC controller |
| E711 |
Document feeder IC failure |
| E716 |
Cassette feed IC failure |
| E800 |
Auto power-off circuit problem |
| E901 |
Cassette feed motor |
| E902 |
Paper guide home sensor problem |
Canon 6035
| Код ошибки |
Описание |
| E000 |
Fuser did not heat up. Lamp, thermal switch, thermistors,
connections, AC driver, DC controller, SSR, etc |
| E001 |
Fuser temperature too high. Same possibilities as E000, as well
as shorted wire |
| E002 |
Fuser temperature not rising at correct pace. Same possibilities
as E000 |
| E003 |
Fuser temperature drops. Same as E003 |
| E004 |
Fuser problem. AC driver, SSR bad, wire shorted |
| E010 |
Drive problem. Main motor, gears, etc |
| E030 |
Total counter |
| E064 |
Composite power board or DC controller |
| E065 |
Composite power board or DC controller |
| E202 |
Scan motor or scan sensor problem. Panel locked with no Код
ошибки. Scan motor problem |
| E203 |
Scan problem or scan sensor |
| E204 |
Scan problem or scan sensor |
| E210 |
Lens sensor or motor problem |
| E212 |
Lens sensor or motor problem |
| E220 |
Exposure lamp or exposure lamp regulator board |
| E224 |
Blanking shutter motor or sensor |
| E240 |
DC controller or composite power supply problem |
| E244 |
DC controller |
| E400 |
RDF to copier communication problem |
| E401 |
RDF Pickup motor or pick up sensor |
| E403 |
RDF feed motor or pulse sensor |
| E404 |
RDF delivery motion problem |
| E404 |
RDF delivery motor problem |
| E411 |
RDF tray sensor or registration sensor |
| E500 |
Sorter main board or communication with copier |
| E510 |
Sorter feed motor |
| E530 |
Sorter guide bar motor |
| E531 |
Sorter stapler motor |
| E540 |
Sorter bin shift motor |
| E541 |
Sorter bin motor |
| E550 |
Sorter power supply |
| E710 |
DC controller |
| E711 |
DC controller |
| E712 |
Document feeder IC failure |
| E716 |
DC controller. Sorter |
| E800 |
Auto power off function (DC controller) |
| E901 |
Pedistal motor |
| E902 |
Jogger side plate sensor or motor |
Canon 6045
| Код ошибки |
Описание |
| E000 |
Fuser did not heat up. Lamp, thermal switch, thermistors,
connections, AC driver, DC controller, SSR, etc |
| E001 |
Fuser temperature too high. Same possibilities as E000, as well
as shorted wire |
| E002 |
Fuser temperature not rising at correct pace, same possibilities
as E000 |
| E003 |
Fuser temperature drops. Same as E000 |
| E004 |
Fuser problem: AC driver, SSR bad, wire shorted |
| E005 |
Fuser cleaning web, or problem with sensor, lever or connector.
Service mode 6 is the probably reset for this |
| E006 |
Fuser feed connector |
| E010 |
Drive problem. Main motor, gears, etc |
| E013 |
Waste toner drive problem, or waste toner sensor switch has been
actuated too many times |
| E015 |
Pickup motor power supply. Could be bad motor or motor board, or
DC controller |
| E020 |
Problem with developer unit, toner hopper, hopper motor,
connection, sensor or DC controller |
| E030 |
Total counter |
| E031 |
Option counter or total counter |
| E050 |
Holding tray (duplex) home position sensor motor or board |
| E051 |
Holding tray (duplex) home sensor motor or board |
| E202 |
Panel locked up, but might be no Код ошибки, scan motor
problem |
| E203 |
Scan problem or scan sensor |
| E204 |
Scan problem or scan sensor |
| E210 |
Lens sensor or motor problem |
| E212 |
Lens sensor or motor problem |
| E213 |
Scan lock sensor or lock solenoid |
| E220 |
Exposure lamp regulator board |
| E240 |
DC controller or composite power supply problem |
| E243 |
DC controller |
| E400 |
RDF to copier communication problem |
| E401 |
RDF pickup motor or pickup sensor |
| E402 |
RDF belt motor or pulse sensor |
| E403 |
RDF feed motor or pulse sensor |
| E411 |
RDF tray sensor or registration sensor |
| E500 |
Sorter main board or communication with copier |
| E510 |
Sorter feed motor |
| E522 |
Sorter push bar motor |
| E523 |
Sorter reference wall motor |
| E524 |
Sorter multi-guide motor |
| E525 |
Sorter bin paper sensor automatic adjustment problem |
| E526 |
Sorter bin paper sensor automatic adjustment problem |
| E530 |
Sorter guide bar motor |
| E531 |
Sorter stapler motor |
| E532 |
Stapler motor |
| E533 |
Stapler inside paper sensor |
| E540 |
Sorter bin shift motor |
| E550 |
Sorter power supply |
| E710 |
DC controller |
| E711 |
DC controller |
| E712 |
Document feeder IC failure |
| E713 |
DC controller, sorter |
| E800 |
Auto power off circuit problem. Main switch or DC
controller |
| E802 |
Auto power off circuit problem. Main switch or DC
controller |
Canon
6085
| Код ошибки |
Описание |
| E000 |
After power-on, the upper fixing roller does not reach 100 C
within 5 min |
| E001 |
The temperature of the upper fixing roller exceeds 230 C for 5
sec or more |
| E002 |
After the temperature of the upper fixing roller has exceeded
100 C, it does not reach 180 C within 5 min |
| E003 |
After the temperature of the upper fixing roller has reached 180
C, it drops to 100 C or less for 5 sec or more |
| E005 |
The length used of the cleaning belt inside the fixing assembly
has exceeded a specific value |
| E012 |
After the drum motor drive signal has been generated, clock
pulses are not generated within 2 sec |
| E013 |
After the waste toner feeding screw has become locked, the
detecting switch (SW20) is pressed a multiple number of times within
a specific period of time |
| E014 |
When the fixing motor (M17) is rotating, an error is detected
for 2 sec or more |
| E015 |
After the pick up motor drive signal has been generated, clock
pulses have not been generated within 2 sec |
| E019 |
As many as 50,000 have been made after detecting a waste toner
full condition |
| E020 |
During copying, the toner supply signal is 0', indicating the
absence of toner, for 3 min or more. During toner supply sequence at
time of installation, the toner supply signal does not go '1' after
6 min or more |
| E030 |
After the total copy counter has turned OFF, an open circuit is
detected for the total copy counter |
| E032 |
After the clock pulse signal reached the IPC communication
format of the copier DC controller PCB, the Copy Data Controller-A1
does not detect the signal |
| E050 |
While the paper jogging guide motor (M11) drive signal is being
generated, the paper guide home position signal (THP) is not
generated for 2 sec or more. While the paper jogging guide motor
(M11) is being generated, the paper jogging guide home position
signal (THP) is generated for two sec or more |
| E202 |
The scanner home position signal (SCHP) is not generated within
10 sec after the power switch or the Copy Start Key is pressed |
| E203 |
While the scanner motor drive signal is being generated, clock
pulses are not generated within 2 sec |
| E204 |
The scanner leading edge signal (SCDP1) is not generated within
0.8 sec after the scanner has started to move |
| E209 |
The scanner C.F.F. position signal (SCFFP) is not generated
within 10 sec after the C.F.F. has been sent |
| E210 |
The lens X home position signal (SCFFP) is not generated within
10 sec after the C.F.F. has been sent |
| E212 |
The lens Y home position signal (LYHP) is not generated within 9
sec after the power switch or the Copy Start Key is turned ON. The
lens Y home position signal (LYHP) is generated for 2 sec or
more |
| E213 |
In stream reading mode, the scanner original leading edge sensor
2 signal (SCDP2) is not generated for 5 pages continuously |
| E214 |
While the scanner cooling fan (FM1, FM10, FM11) is rotating, an
error signal is generated for 2 sec or more |
| E270 |
In stream reading mode, the scanner leading edge signal(SCDP2)
is not generated within a specific period of time after a command
has been issued to lock the scanner |
| E710 |
At power-on the IPC (Q170) on the DC controller PCB cannot be
initialized |
| E711 |
After power-on the IPC (Q170) on the DC controller PCB goes out
of order |
| E712 |
The communication IC on the RDF controller PCB has gone out of
order |
| E713 |
The communication IC on the sorter control PCB has gone out of
order |
| E715 |
The communication IC on the C.F.F. controller PCB has gone out
of order |
| E717 |
The communication IC on the Copy Data Controller-A1 PCB has gone
out of order |
| E800 |
An open circuit is detected |
| E801 |
Current flows from the activation circuit in the absence of the
scanning lamp ON signal |
| E802 |
The relay (RL3) in the power supply unit does not operate in
spite of the auto power-off signal |
Canon 6150
| Код ошибки |
Описание |
| E000 |
Thermistor |
| E001 |
SSR |
| E002 |
Thermistor, ht. Lamp thermal fuse or SSR |
| E003 |
Thermistor, ht. Lamp thermal fuse or SSR |
| E005 |
Fuser cleaning belt |
| E010 |
Main drive problem |
| E020 |
Toner motor, toner level sensor, toner hopper sensor |
| E030 |
Counter |
| E050 |
Duplex problem |
| E203 |
Scan home problem |
| E210 |
Lens home sensor |
| E401 |
Document feeder paper pickup motor |
| E402 |
Document feeder belt clock pulse problem |
| E403 |
Document feeder main motor clock pulse problem |
| E411 |
Document feeder sensor problem |
| E500 |
Sorter/copier interface problem |
| E510 |
Sorter motor drive |
| E530 |
Sorter home sensor |
| E531 |
Stapler swing sensor |
| E540 |
Sorter lead cam home sensor |
| E541 |
Sorter lead cam home sensor |
| E710 |
DC controller board |
| E711 |
DC controller board |
| E712 |
Document feeder problem |
Canon 6212
| Код ошибки |
Описание |
| C |
No problem. Means that the machine is correcting the fuser film
tracking. |
| CC |
Drum must be changed. Could be the drum serial number is
identified by the logic as being non-compatible to that particular
copier. |
| E000 |
Low fuser temperature |
| E001 |
High fuser temperature |
| E002 |
High fuser temperature |
| E003 |
Erratic fuser temperature |
| E007 |
Fuser film off track and will not repair itself |
| E010 |
Main drive problem |
| E030 |
Counter problem |
| E064 |
Scan problem, or power supply |
| E202 |
Scan problem |
| E210 |
Lens drive problem or lens sensor |
| E220 |
Exposure lamp stays on or off |
| E240 |
DC controller (main board) or composite power supply |
| E261 |
Zero cross problem. Power frequency or composite power
supply |
| E400 |
Communication problem between boards |
| E803 |
24 volt problem |
| EO |
Fuser problem |
| H |
Fuser overheat |
Canon 6230
| Код ошибки |
Описание |
| E000 |
Fuser did not heat up. Lamp, thermal switch, thermistors,
connections, AC driver, DC controller, SSR, etc |
| E001 |
Fuser temperature too high. Same possibilities as E000, as well
as shorted wire |
| E002 |
Fuser temperature not rising at correct pace. Same possibilities
as E000 |
| E003 |
Fuser temperature drops. Same as E003 |
| E004 |
Fuser problem. AC driver, SSR bad, wire shorted |
| E010 |
Drive problem. Main motor, gears, etc |
| E030 |
Total counter |
| E064 |
Composite power board or DC controller |
| E065 |
Composite power board or DC controller |
| E202 |
Scan motor or scan sensor problem. Panel locked with no Код
ошибки. Scan motor problem |
| E203 |
Scan problem or scan sensor |
| E204 |
Scan problem or scan sensor |
| E210 |
Lens sensor or motor problem |
| E212 |
Lens sensor or motor problem |
| E220 |
Exposure lamp or exposure lamp regulator board |
| E224 |
Blanking shutter motor or sensor |
| E240 |
DC controller or composite power supply problem |
| E244 |
DC controller |
| E400 |
RDF to copier communication problem |
| E401 |
RDF Pickup motor or pick up sensor |
| E403 |
RDF feed motor or pulse sensor |
| E404 |
RDF delivery motion problem |
| E404 |
RDF delivery motor problem |
| E411 |
RDF tray sensor or registration sensor |
| E500 |
Sorter main board or communication with copier |
| E510 |
Sorter feed motor |
| E530 |
Sorter guide bar motor |
| E531 |
Sorter stapler motor |
| E540 |
Sorter bin shift motor |
| E541 |
Sorter bin motor |
| E550 |
Sorter power supply |
| E710 |
DC controller |
| E711 |
DC controller |
| E712 |
Document feeder IC failure |
| E716 |
DC controller. Sorter |
| E800 |
Auto power off function (DC controller) |
| E901 |
Pedistal motor |
| E902 |
Jogger side plate sensor or motor |
Canon 6650
| Код ошибки |
Описание |
| E000 |
Thermistor |
| E001 |
SSR |
| E002 |
Thermistor, ht. Lamp thermal fuse or SSR |
| E003 |
Thermistor, ht. Lamp thermal fuse or SSR |
| E005 |
Fuser cleaning belt |
| E010 |
Main drive problem |
| E020 |
Toner motor, toner level sensor, toner hopper sensor |
| E030 |
Counter |
| E050 |
Duplex problem |
| E203 |
Scan home problem |
| E210 |
Lens home sensor |
| E401 |
Document feeder paper pickup motor |
| E402 |
Document feeder belt clock pulse problem |
| E403 |
Document feeder main motor clock pulse problem |
| E411 |
Document feeder sensor problem |
| E500 |
Sorter/copier interface problem |
| E500 |
An error is identified in the communication between the sorter
and the copier |
| E510 |
The clock signal from the motor is absent for 250ms or
more |
| E510 |
Sorter motor drive |
| E513 |
The clock signal from the motor is absent for 250 ms or
more |
| E530 |
Sorter home sensor |
| E530 |
The home position sensor (P17) fails to go OFF when an
equivalent of 2560 pulses of the motor drive command has been
generated |
| E531 |
The stapler unit swing sensor (MS9) fails to go ON within 500 ms
after the motor drive command has been generated. MS9 fails to go
back OFF within 1000 ms after it has gone on |
| E531 |
Stapler swing sensor |
| E540 |
The lead cam home position sensor (P12) fails to go OFF within
2000 ms after the motor drive command has been generated. P12 fails
to go back ON within 2000 ms after it has gone OFF |
| E540 |
Sorter lead cam home sensor |
| E541 |
Sorter lead cam home sensor |
| E710 |
DC controller board |
| E711 |
DC controller board |
| E712 |
Document feeder problem |
Canon 7050
| Код ошибки |
Описание |
| E000 |
Heater (Reset by unplugging machine) |
| E001 |
Heater triac, DC controller, AC driver (reset by
unplugging) |
| E005 |
Fuser cleaner belt at end. Replace |
| E010 |
Main motor, DC controller or DC driver board |
| E011 |
Any motor ( main, scan, cleaner belt, duplex, toner, lens) DC
driver, DC controller, duplex driver board |
| E020 |
Toner out signal has been sent for at least 3 minutes |
| E050 |
Duplex |
| E203 |
Scan motor, DC driver, DC controller |
| E210 |
Lens home sensor not actuated or won't deactuate |
| E240 |
Controller board |
| E241 |
Controller board |
| E242 |
Controller board |
| E400 |
DC controller, Doc. Feeder board, 24V power supply |
| E500 |
DC controller, sorter board, 24V power
supply |
Canon
720, 740, 770, 790
| Код ошибки |
Описание |
| C |
No problem. Means that the machine is correcting the fuser film
tracking |
| CC |
Drum must be changed. Could be the drum serial number is
identified by the logic as being non-compatible to that particular
copier |
| E000 |
Low fuser temperature |
| E001 |
High fuser temperature |
| E002 |
High fuser temperature |
| E003 |
Erratic fuser temperature |
| E007 |
Fuser film off track and will not repair itself |
| E010 |
Main drive problem |
| E030 |
Counter problem |
| E064 |
Scan problem, or power supply |
| E202 |
Scan problem |
| E210 |
Lens drive problem or lens sensor |
| E220 |
Exposure lamp stays on or off |
| E240 |
DC controller (main board) or composite power supply |
| E261 |
Zero cross problem. Power frequency or composite power
supply |
| E400 |
Communication problem between boards |
| E803 |
24 volt problem |
| E0 |
Fuser problem |
| H |
Fuser overheat |
Canon 7550
| Код ошибки |
Описание |
| E000 |
Heater (Reset by unplugging machine) |
| E001 |
Heater triac, DC controller, AC driver (reset by
unplugging) |
| E005 |
Fuser cleaner belt at end. Replace |
| E010 |
Main motor, DC controller or DC driver board |
| E011 |
Any motor ( main, scan, cleaner belt, duplex, toner, lens) DC
driver, DC controller, duplex driver board |
| E020 |
Toner out signal has been sent for at least 3 minutes |
| E050 |
Duplex |
| E203 |
Scan motor, DC driver, DC controller |
| E210 |
Lens home sensor not actuated or won't deactuate |
| E240 |
Controller board |
| E241 |
Controller board |
| E242 |
Controller board |
| E400 |
DC controller, Doc. Feeder board, 24V power supply |
| E500 |
DC controller, sorter board, 24V power
supply |
Canon
8070, 8570
| Код ошибки |
Описание |
| E000 |
Fuser problem. Temperature too low. Heat lamp, thermal fuse or
thermoswitch, thermistor, triac etc |
| E001 |
Fuser problem. Temperature too high. Probably triac |
| E005 |
Fuser web finished |
| E005 |
Fuser cleaner belt user up |
| E010 |
Drive |
| E010 |
Main drive problem |
| E011 |
Drive problem. Could be main motor, scan motor, cleaning web
motor or duplex motor |
| E020 |
Toner empty sensor sees no toner added for 3 min probably toner
feed problem |
| E050 |
Duplex problem |
| E203 |
Scan motor |
| E210 |
Lens home sensor or lens won't leave home |
| E240 |
DC controller board |
| E241 |
DC controller board |
| E242 |
DC controller board |
| E243 |
Operation panel board |
| E400 |
DC controller, ADF board or 24V |
| E500 |
DC controller, sorter board or 24V |
| E510 |
Finisher; feed motor, pulse sensor, finisher board |
| E520 |
Finisher; stack motor, stack tray sensor, finisher board |
| E530 |
Finisher; guide plate motor, stapler guide, finisher board |
| E531 |
Finisher; staple motor, staple sensor, finisher
board |
Canon
8530, 8580
| Код ошибки |
Описание |
| E000 |
The surface temperature of the fixing assembly upper roller
fails to rise by a specified value within 90 sec after power-on. The
surface temperature of the fixing assembly upper roller fails to
reach 150C within 8 min after power on. The surface temperature of
the fixing assembly upper roller fails to reach 180C within 5 min
after it has reached 150C. The surface temperature of the fixing
assembly upper roller falls below 50C in standby |
| E001 |
The surface temperature of the fixing assembly upper roller
exceeds 250C |
| E005 |
The cleaning belt inside the fixing assembly has been taken up
more than a specified length |
| E010 |
After generation of the main motor drive signal, two or more
pulses are not received within 2 sec |
| E020 |
The accumulative time during which the toner supply signal (TSP)
has been generated by the developing assembly reaches 3 min |
| E050 |
The holding tray home position signal (THP) is not generated
within 4 sec while the holding tray motor drive signal (TMDP1,2) is
being generated. The holding tray home position signal (THP) is
generated 1 sec or more while the holding tray motor drive signal
(TMDP1.2) is being generated |
| E13 |
The error detection circuit on the waste toner feed motor driver
PCB has detected on overcurrent |
| E203 |
Input of two or more clock pulses is not received within 2 sec
from the scanner motor drive signal is generated |
| E210 |
The lens home position signal (LHP) is not generated within 4.8
sec after the power switch or door switch has gone ON. The lens home
position signal (LHP) is generate 2 sec or more |
| E240 |
An error has occurred in the microprocessor on the DC controller
PCB |
| E243 |
An error has occurred in the communication between the
microprocessor of the DC controller PCB and the microprocessor in
the control panel |
| E710 |
An error has occurred in the communication between the DC
controller PCB and the controller PCB of the option, and the DC
controller has detected the error |
Canon 9800
| Код ошибки |
Описание |
| E000 |
The surface temperature of the fixing assembly upper roller
fails to rise by a specified value within 90 sec after power-on. The
surface temperature of the fixing assembly upper roller fails to
reach 150C within 8 min after power-on |
| E001 |
The surface temperature of the fixing assembly upper roller
exceeds 250C |
| E005 |
The cleaning belt inside the fixing assembly has been taken up
more than a specified length |
| E010 |
After generation of the main motor drive signal, two or more
pulses are not received within 2 sec |
| E013 |
The error detection circuit on the waste toner feed motor driver
PCB has detected an overcurrent |
| E020 |
The accumulative time during which the toner supply signal (TSP)
has been generated by the developing assembly reaches 3 min* |
| E050 |
The holding tray home position signal (THP) is not generated
within 4 sec while the holding tray motor drive signal (TMDP1, 2) is
being generated. The holding tray home position signal (THP) is
generated 1 sec or more while the holding tray motor drive signal
(TMDP1, 2) is being generated |
| E203 |
Input of two or more clock pulses is not received within 2 sec
from the scanner motor drive signal is generated |
| E210 |
The lens home position signal (LHP) is not generated within 4.8
sec after power switch or door switch has gone ON. The lens home
position signal (LHP) is generate 2 sec or more |
| E240 |
An error has occurred in the microprocessor on the DC controller
PCB |
| E243 |
An error has occurred in the microprocessor of the DC controller
PCB and the microprocessor in the control panel |
| E710 |
An error has occurred in the communication between the DC
controller PCB and the controller PCB of the option, and the DC
controller has detected the error |
| E712 |
No communication is perceived from the RF controller PCB for 200
ms or more the communication is monitored at all
times |
Canon
A-1
| Код ошибки |
Описание |
| E500 |
An error is identified in the communication between the sorter
and copier |
| E510 |
The clock signal from the motor is absent for 250 ms or
more |
| E513 |
The clock signal from the motor is absent for 250 ms or
more |
| E530 |
The home position sensor (P17) fails to go OFF when an
equivalent of 2560 pulses of the motor drive command has been
generated |
| E531 |
The stapler unit swing sensor (MS9) fails to go ON within 500 ms
after the motor drive command has been generated. MS9 fails to go
back OFF within 1000 ms after it has gone ON |
| E540 |
The lead cam home position sensor (P12) fails to go OFF within
2000 ms after the motor drive command has been generated. P12 fails
to go back ON within 2000 ms after it has gone
OFF |
Canon
C-120
| Код ошибки |
Описание |
| C |
No problem. Means that the machine is correcting the fuser film
tracking |
| CC |
Drum must be changed. Could be the drum serial number is
identified by the logic as being non-compatible to that particular
copier |
| E000 |
Low fuser temperature |
| E001 |
High fuser temperature |
| E002 |
High fuser temperature |
| E003 |
Erratic fuser temperature |
| E007 |
Fuser film off track and will not repair itself |
| E010 |
Main drive problem |
| E030 |
Counter problem |
| E064 |
Scan problem, or power supply |
| E202 |
Scan problem |
| E210 |
Lens drive problem or lens sensor |
| E220 |
Exposure lamp stays on or off |
| E240 |
DC controller (main board) or composite power supply |
| E261 |
Zero cross problem. Power frequency or composite power
supply |
| E400 |
Communication problem between boards |
| E803 |
24 volt problem |
| E0 |
Fuser problem |
| H |
Fuser overheat |
Canon C-160
| Код ошибки |
Описание |
| E000 |
Fuser thermistor, heater, thermal fuse |
| E001 |
Fuser thermistor, or triac |
| E002 |
Fuser thermistor, thermal fuse or triac |
| E003 |
Fuser thermistor, heater, thermal fuse or triac |
| E004 |
Triac or fuser won't shut off |
| E007 |
Fuser film is off center or not driving properly |
| E010 |
Main motor drive problem |
| E030 |
Counter |
| E064 |
Composite power supply or main board |
| E202 |
Scan problem |
| E210 |
Lens drive problem |
| E220 |
Exposure lamp |
| E240 |
Main board or composite power supply |
| E261 |
Composite power supply or fluctuating power |
| E400 |
ADF communication problem to machine |
| E402 |
ADF belt motor drive |
| E404 |
ADF exit motor |
| E411 |
ADF document detect, or registration sensor or edge sensor |
| E500 |
Sorter communication problem |
| E510 |
Sorter drive problem |
| E530 |
Stapler guide bar motor |
| E531 |
Stapler swing motor |
| E540 |
Bin shift motor |
| E541 |
Bin motor drive problem |
| E710 |
Main board |
| E711 |
Main board |
| E712 |
Main board or communication problem with ADF |
| E717 |
Main board, asst. board |
| U0 |
Initializing. Sets all user modes to factory default
settings |
| U1 |
Auto clear timer. Range 1-9. Each digit=1 minute |
| U2 |
Automatic power shut off timer |
| U3 |
Fine adjustment of zoom |
| U4 |
Auto cassette switching |
| U5 |
Sort or non-sort default |
| U6 |
Cleans document feeder pickup assembly |
| U7 |
CLEAR "replace drum" |
| U9 |
Auto exposure or manual exposure as
default |
Canon
C-180
| Код ошибки |
Описание |
| E000 |
Fuser problem. Low temperature. Lamp, thermal switch, AC
driver |
| E001 |
Fuser problem. High temperature. Triac, AC driver, pinched
wire |
| E004 |
Fuser problem |
| E0053 |
Sorter |
| E030 |
Counter |
| E202 |
Scan |
| E210 |
Lens |
| E221 |
Exposure lamp regulator board, thermal fuse, exposure lamp |
| E400 |
Automatic document feeder |
| E500 |
Sorter |
| E710 |
DC controller |
Canon C200D
| Код ошибки |
Описание |
| E000 |
Fuser thermistor, heater thermal fuse |
| E001 |
Fuser thermistor, or triac |
| E002 |
Fuser thermistor, thermal fuse or triac |
| E003 |
Fuser thermistor, heater, thermal fuse or triac |
| E004 |
Triac or fuser won't shut off |
| E007 |
Fuser film is off center or not driving properly. Might be able
to reset in service mode 4-407 |
| E010 |
Main motor drive problem |
| E030 |
Counter |
| E041 |
Paper deck motor, clutch or sensor |
| E064 |
Composite power supply or main motor board |
| E202 |
Scan problem. Motor sensor |
| E210 |
Lens drive problem |
| E220 |
Exposure lamp |
| E240 |
Main board or composite power supply |
| E260 |
Main board, power supply cooling fan or composite power
supply |
| E261 |
Composite power supply or fluctuating power |
| E400 |
ADF communication to machine |
| E401 |
ADF pickup motor or sensor |
| E402 |
ADF belt motor drive |
| E403 |
ADF feed motor or slip sensor |
| E404 |
ADF exit motor |
| E411 |
ADF document detect, or registration sensor or edge sensor |
| E500 |
Sorter communication problem |
| E510 |
Sorter drive problem |
| E530 |
Stapler guide bar motor |
| E531 |
Stapler swing motor |
| E540 |
Bin shift motor |
| E541 |
Bin motor drive problem |
| E710 |
Main board (DC controller.) |
| E711 |
Main board (DC controller.) |
| E712 |
Main board or communication problem with ADF, or ADF main
board |
| E717 |
Main board, assist board. "Replace drum": Drum waste toner is
full, or drum has run 40,000 copies. Reset with user |
| E802 |
Composite power supply or DC controller |
| E901 |
Cassette feed unit board or cassette feed motor |
| E902 |
Horizontal registration problem. I think this refers to the
duplex section |
| J1 |
Feed jam |
| J10 |
Duplex exit jam |
| J11 |
Vertical jam |
| J12 |
Vertical jam |
| J13 |
Vertical jam |
| J14 |
Vertical jam |
| J15 |
Deck jam |
| J2 |
Feed jam |
| J3 |
Separation area jam |
| J4 |
Separation area jam |
| J5 |
Exit jam |
| J6 |
Exit jam |
| J7 |
Sorter jam |
| J8 |
Door open jam |
| J9 |
Cassette jam |
| JA |
Cassette jam |
| Jb |
Cassette jam |
| JC |
Cassette jam |
| Jd |
Duplex feed jam |
| JE |
Duplex exit jam |
| JF |
Duplex registration jam |
Canon NP
| Код ошибки |
Описание |
| E000 |
Fuser thermistor, heater thermal fuse |
| E001 |
Fuser thermistor, or triac |
| E002 |
Fuser thermistor, thermal fuse or triac |
| E003 |
Fuser thermistor, heater, thermal fuse or triac |
| E004 |
Triac or fuser won't shut off |
| E007 |
Fuser film is off center or not driving properly. Might be able
to reset in service mode 4-407 |
| E010 |
Main motor drive problem |
| E030 |
Counter |
| E041 |
Paper deck motor, clutch or sensor |
| E064 |
Composite power supply or main motor board |
| E202 |
Scan problem. Motor sensor |
| E210 |
Lens drive problem |
| E220 |
Exposure lamp |
| E240 |
Main board or composite power supply |
| E260 |
Main board, power supply cooling fan or composite power
supply |
| E261 |
Composite power supply or fluctuating power |
| E400 |
ADF communication to machine |
| E401 |
ADF pickup motor or sensor |
| E402 |
ADF belt motor drive |
| E403 |
ADF feed motor or slip sensor |
| E404 |
ADF exit motor |
| E411 |
ADF document detect, or registration sensor or edge sensor |
| E500 |
Sorter communication problem |
| E510 |
Sorter drive problem |
| E530 |
Stapler guide bar motor |
| E531 |
Stapler swing motor |
| E540 |
Bin shift motor |
| E541 |
Bin motor drive problem |
| E710 |
Main board (DC controller.) |
| E711 |
Main board (DC controller.) |
| E712 |
Main board or communication problem with ADF, or ADF main
board |
| E717 |
Main board, assist board. "Replace drum": Drum waste toner is
full, or drum has run 40,000 copies. Reset with user |
| E802 |
Composite power supply or DC controller |
| E901 |
Cassette feed unit board or cassette feed motor |
| E902 |
Horizontal registration problem. I think this refers to the
duplex section |
| J1 |
Feed jam |
| J10 |
Duplex exit jam |
| J11 |
Vertical jam |
| J12 |
Vertical jam |
| J13 |
Vertical jam |
| J14 |
Vertical jam |
| J15 |
Deck jam |
| J2 |
Feed jam |
| J3 |
Separation area jam |
| J4 |
Separation area jam |
| J5 |
Exit jam |
| J6 |
Exit jam |
| J7 |
Sorter jam |
| J8 |
Door open jam |
| J9 |
Cassette jam |
| JA |
Cassette jam |
| Jb |
Cassette jam |
| JC |
Cassette jam |
| Jd |
Duplex feed jam |
| JE |
Duplex exit jam |
| JF |
Duplex registration jam |
Canon PC
| Код ошибки |
Описание |
| C |
No problem. Means that the machine is correcting the fuser film
tracking |
| CC |
Drum must be changed. Could be the drum serial number is
identified by the logic as being non-compatible to that particular
copier |
| E000 |
Low fuser temperature |
| E001 |
High fuser temperature |
| E002 |
High fuser temperature |
| E003 |
Erratic fuser temperature |
| E007 |
Fuser film off track and will not repair itself |
| E010 |
Main drive problem |
| E030 |
Counter problem |
| E064 |
Scan problem, or power supply |
| E202 |
Scan problem |
| E210 |
Lens drive problem or lens sensor |
| E220 |
Exposure lamp stays on or off |
| E240 |
DC controller (main board) or composite power supply |
| E261 |
Zero cross problem. Power frequency or composite power
supply |
| E400 |
Communication problem between boards |
| E803 |
24 volt problem |
| EO |
Fuser problem |
| H |
Fuser overheat |
| E000 |
Fuser thermistor, heater, thermal fuse |
| E001 |
Fuser thermistor, or triac |
| E002 |
Fuser thermistor, thermal fuse or triac |
| E003 |
Fuser thermistor, heater, thermal fuse or triac |
| E004 |
Triac or fuser won't shut off |
| E007 |
Fuser film is off center or not driving properly |
| E010 |
Main motor drive problem |
| E030 |
Counter |
| E064 |
Composite power supply or main board |
| E202 |
Scan problem |
| E210 |
Lens drive problem |
| E220 |
Exposure lamp |
| E240 |
Main board or composite power supply |
| E261 |
Composite power supply or fluctuating power |
| E400 |
ADF communication problem to machine |
| E402 |
ADF belt motor drive |
| E404 |
ADF exit motor |
| E411 |
ADF document detect, or registration sensor or edge sensor |
| E500 |
Sorter communication problem |
| E510 |
Sorter drive problem |
| E530 |
Stapler guide bar motor |
| E531 |
Stapler swing motor |
| E540 |
Bin shift motor |
| E541 |
Bin motor drive problem |
| E710 |
Main board |
| E711 |
Main board |
| E712 |
Main board or communication problem with ADF |
| E717 |
Main board, asst. board |
| U0 |
Initializing. Sets all user modes to factory default
settings |
| U1 |
Auto clear timer. Range 1-9. Each digit=1 minute |
| U2 |
Automatic power shut off timer |
| U3 |
Fine adjustment of zoom |
| U4 |
Auto cassette switching |
| U5 |
Sort or non-sort default |
| U6 |
Cleans document feeder pickup assembly |
| U7 |
CLEAR "replace drum" |
| U9 |
Auto exposure or manual exposure as default |
| EO |
Heater problem |
| E1 |
The heater film has gone off center. Turn machine off & on,
make sure it's level etc |
| E2 |
Scan problme |
| E6 |
Exposure lamp or exposure lamp sensor |
| E000 |
Fuser problem |
| E001 |
Fuser problem |
| E010 |
Drive |
| E210 |
Zoom/lens/motor problem |
| E00 |
Heater, thermoswitch, exit sensor (Reset by jumping CP102 pins 1
& 2, or leave machine off for 20 seconds |
| E001 |
Shorted thermistor or high-temperature, Exit sensor |
| E010 |
Clock Pulse |
| E210 |
Zoom Lens Problem |
Canon PC6
| Код ошибки |
Описание |
| E000 |
Fuser problem |
| E001 |
Fuser problem |
| E010 |
Drive |
| E210 |
Zoom/lens/motor problem |
Canon PC7
| Код ошибки |
Описание |
| E00 |
Heater, thermoswitch, exit sensor (Reset by jumping CP102 pins 1
& 2, or leave machine off for 20 seconds |
| E001 |
Shorted thermistor or high-temperature, Exit sensor |
| E010 |
Clock Pulse |
| E210 |
Zoom Lens Problem |
Canon NP7161
| Код ошибки |
Описание |
| E000 |
The thermistor (TH1, TH2) has poor contact or an open circuit
The fixing heater (H1) has an open circuit
The thermal switch (TSW1) has turned on
The triac is faulty
The DC controller PCB is faulty |
| E001 |
The thermistor (TH1, TH2) has a short circuit
The triac is faulty
The DC controller PCB is faulty |
E002
E003 |
The thermistor (TH1, TH2) has poor contact or an open circuit
The fixing heater (H1) has an open circuit
The thermal switch (TSW1) has turned on
The triac is faulty
The DC controller PCB is faulty |
| E004 |
The triac has a short circuit
The DC controller PCB is faulty |
| E010 |
The main motor (M1) is faulty
The DC controller PCB is faulty |
| E013 |
The waste toner feedscrew is locked
The waste toner feedscrew lock sensor (PS8) is faulty
The DC controller PCB is faulty |
| E030 |
The total copy counter has an open circuit
The DC controller PCB is faulty |
| E031 |
The accessories counter has an open circuit
The DC controller PCB is faulty |
| (E202) |
No code indication. Keys are disabled
The scanner home position sensor (PS1) is faulty
The scanner motor (M2) is faulty
The DC controller PCB is faulty |
| E208 |
The mirror home position sensor (PS3) is faulty
The mirror motor (M4) is faulty
The DC controller PCB is faulty |
| E210 |
The lens home position sensor (PS2) is faulty
The lens motor (M3) is faulty
The DC controller PCB is faulty |
| E220 |
The lamp regulator PCB is faulty
The DC controller PCB is faulty |
| E261 |
The power supply frequency is faulty
The power supply PCB is faulty |
E710
E711 |
The DC controller PCB is faulty |
| E712 |
The DC controller PCB is faulty
The ADF controller PCB is fault
The ADF cable is faulty |
| E717 |
The DC controller PCB is faulty
The Remote Diagnostic Device II PCB is faulty |
| E800 |
The auto power-off circuit has an open circuit
The DC controller PCB is faulty |
| E805 |
The exhaust fan (FM2, FM4) is faulty
The DC controller PCB is faulty |
| E821 |
The ozone filter is clogged
The cleaner thermistor (TH3) has poor contact or an open circuit
The DC controller PCB is faulty |
Вы находитесь: Главная
|
Ремонт принтеров
